What to do if my Makita EA6101P Chainsaw engine does not start?
If the engine of your Makita Chainsaw does not start easily, it could be due to a malfunction in the fuel supply system, the compression system, or a mechanical malfunction. Make sure the fuel tank is full, inspect the ignition system, and ensure that the starter engages properly.
Why my Makita EA6101P engine does not start or starts with difficulty?
If your Makita Chainsaw engine won't start or starts with difficulty, it could be due to a malfunction in the fuel supply or compression system, or a mechanical malfunction. Check if the STOP switch is actuated, or if there's a fault or short-circuit in the spark plug cap or the spark plug itself is defective. Other potential issues include the combination switch being in the Choke position, a defective carburetor, a dirty suction head, or a bent or interrupted fuel line. Additionally, inspect the cylinder base packing ring, radial shaft packings, cylinder or piston rings, and ensure the spark plug seals correctly. Finally, a broken spring in the starter or broken parts inside the engine could also be the cause.
What to do if my Makita EA6101P starts, but dies immediately?
If your Makita Chainsaw starts but immediately dies, the issue might be due to an incorrect idling adjustment or a dirty suction head or carburetor. You should inspect and clean the suction head and carburetor, and then adjust the idling as needed.
Why is there no chain lubrication in my Makita EA6101P Chainsaw?
If there is no chain lubrication in your Makita Chainsaw, this could be because the oil tank is empty, the oil guide groove is dirty, or the oil pump adjusting screw is incorrectly adjusted. Refill the oil tank, clean the oil guide groove, and adjust the oil pump to resolve the issue.
What to do if my Makita Chainsaw engine starts, but dies immediately?
If your Makita Chainsaw engine starts but immediately dies, the issue could stem from several factors. Check for a dirty suction head or carburetor, or an incorrect idling adjustment. Other potential causes include a defective tank venting system, an interrupted fuel line, a defective cable, or a defective combination switch.
Why is there no chain lubrication on my Makita EA6101P?
If your Makita Chainsaw chain is not being lubricated, check if the oil tank is empty. Also, inspect the oil guide groove for dirt and ensure the oil pump adjusting screw is correctly adjusted.
Why does my Makita EA6101P have warm start difficulties?
If you are experiencing warm start difficulties with your Makita Chainsaw, it may be due to wrong carburetor adjustment.
How to troubleshoot insufficient power in Makita Chainsaw?
If your Makita Chainsaw is showing insufficient power, the cause might be a dirty air filter, incorrect carburetor adjustment, a clogged muffler, a clogged exhaust channel in the cylinder, or a clogged spark arrester screen. To resolve this, try cleaning or replacing the air filter, adjusting the carburetor, and clearing any clogs in the muffler, exhaust channel, and spark arrester screen.
What to do if Makita EA6101P starts but dies immediately?
If your Makita Chainsaw starts but immediately dies, the issue could stem from a few potential causes. Check for a wrong idling adjustment, or a dirty suction head or carburetor. Adjust the idling and clean the suction head and carburetor. Additionally, inspect the tank venting, fuel line, cable, and combination switch for any defects.
How to fix no chain lubrication on Makita EA6101P?
If there is no chain lubrication in your Makita Chainsaw, the oil tank might be empty, the oil guide groove could be dirty, or the oil-pump adjusting screw might be incorrectly adjusted. Refill the oil tank, clean the oil guide groove, and adjust the oil-pump adjusting screw.
General| Chain Pitch | 3/8 inch |
|---|---|
| Chain Gauge | 1.5 mm |
| Engine Displacement | 61.5 cc |
| Bar Length | 50 cm |
| Fuel Tank Capacity | 550 ml |
To Next Page
