EasyManua.ls Logo

Makita EA3502S - User Manual

Makita EA3502S
40 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Instruction Manual
Original Instruction Manual
Important:
Read this instruction manual carefully before putting the chain saw into operation and strictly observe the
safety regulations!
Keep this instruction manual!
EA3500S
EA3501S
EA3502S
EA3503S

Table of Contents

Other manuals for Makita EA3502S

Preview: Original Instruction Manual
Original Instruction Manual220 pages

Questions and Answers

  • C
    Chelsea HuntNov 22, 2025
    Why won't my Makita Saw start?
    • I
      Ivan JordanNov 22, 2025
      If your Makita Saw engine isn't starting easily, it could be due to several issues within the fuel supply, compression, or mechanical components. Check for a malfunctioning fuel supply system, compression system, or mechanical malfunction. Also, inspect if the stop switch is in the wrong position, or there's a fault or short-circuit in the wiring. A defective spark plug cap or spark plug could also be the cause. Other potential problems include the combination switch being in the choke position, a defective carburetor, a dirty suction head, a bent or interrupted fuel line, a defective cylinder base packing ring or radial shaft packings, defective cylinder or piston rings, a spark plug that doesn't seal, a broken spring in the starter, or broken parts inside the engine. Inspect and repair t...
  • J
    Jamie LunaAug 25, 2025
    Why won't my Makita EA3502S engine start?
    • M
      Mr. Christopher DayAug 26, 2025
      If your Makita Chainsaw engine is not starting, several factors could be at play. There may be a malfunction in the fuel supply, compression, or mechanical systems. Check and repair the ignition system, fuel supply, or starter as needed. Also, ensure the STOP switch is in the correct position and check the wiring, spark plug cap, and spark plug. Inspect and adjust the combination switch; clean or replace the carburetor and suction head; and check the fuel line. Replace any defective parts in the cylinder or piston. Finally, inspect and replace the starter spring or any broken parts inside the engine.
  • I
    Ian PenaAug 26, 2025
    Why my Makita EA3502S engine does not start?
    • A
      Aaron HamiltonAug 27, 2025
      If your Makita Chainsaw engine is not starting, begin by checking the ignition spark. Also inspect the wiring, and replace the spark plug or cap if defective. Ensure proper spark plug sealing. Adjust the combination switch and clean the carburetor if the combination switch is in Choke position, or if the carburetor is defective, or the suction head is dirty, or the fuel line is bent or interrupted. Finally, inspect the starter and engine parts, and replace defective components if the cylinder base packing ring or radial shaft packings are defective, or if the cylinder or piston rings are defective.
  • T
    Tiffany SloanAug 28, 2025
    How to fix insufficient power in Makita Saw?
    • W
      williamsbarryAug 28, 2025
      If your Makita Saw has insufficient power, the cause might be a dirty air filter, incorrect carburetor adjustment, a clogged muffler, a clogged exhaust channel in the cylinder, or a clogged spark arrester screen. Clean or replace the air filter and muffler.
  • N
    Nancy GibsonNov 26, 2025
    Why Makita EA3502S Chainsaw engine does not start?
    • E
      Erika JonesNov 26, 2025
      There could be several reasons why your Makita Chainsaw engine won't start. It could be a malfunction in the fuel supply, compression, or ignition system. The STOP switch may be in the wrong position, or there might be a fault in the wiring. Other potential causes include a defective spark plug or cap, a dirty carburetor or fuel line, defective packing rings, a spark plug that doesn't seal, or broken parts in the engine or starter. Suggested solutions include inspecting and repairing the ignition system, fuel supply, and compression; ensuring the STOP switch is in the correct position and checking wiring integrity; adjusting the combination switch and cleaning the carburetor and fuel lines; replacing defective packing rings and checking cylinder and piston rings; replacing or reseating the...
  • A
    Arthur WoodSep 15, 2025
    Why is there no chain lubrication in my Makita Saw?
    • S
      Susan RodriguezSep 15, 2025
      If your Makita Saw isn't lubricating the chain, it could be due to an empty oil tank, a dirty oil guide groove, or an incorrectly adjusted oil pump adjusting screw. Fill the oil tank, clean the oil guide groove, and adjust the oil pump.
  • N
    Nicole Clark MDSep 13, 2025
    What to do if my Makita EA3502S Chainsaw engine does not start?
    • P
      Patricia HullSep 13, 2025
      If the engine of your Makita Chainsaw doesn't start or starts with difficulty, there could be a malfunction in the fuel supply system, compression system, or a mechanical malfunction. Check the ignition spark, fuel tank, and starter engagement. Also, inspect for any wiring faults.
  • W
    wmunozSep 14, 2025
    What to do if my Makita Saw starts then dies?
    • W
      whollowaySep 14, 2025
      If your Makita Saw starts but dies immediately, the issue might stem from an incorrect idling adjustment, a dirty suction head or carburetor, a defective tank venting system, an interrupted fuel line, a defective cable, or a defective combination switch. To resolve this, clean the suction head and carburetor, and check the tank venting and fuel line.
  • R
    Ralph EllisSep 6, 2025
    What to do if Makita EA3502S Chainsaw engine starts, but dies immediately?
    • C
      Carrie SharpSep 6, 2025
      If your Makita Chainsaw starts but dies immediately, it could be due to a wrong idling adjustment, or a dirty suction head or carburetor. Adjust the idling and clean the suction head or carburetor. Also, check the tank venting and fuel line, as a defective tank venting, interrupted fuel line, defective cable or combination switch could also be the cause.
  • A
    Adam LynchSep 4, 2025
    How to fix no chain lubrication on a Makita Chainsaw?
    • M
      Matthew ThompsonSep 4, 2025
      If your Makita Chainsaw isn't lubricating the chain, the oil tank might be empty, the oil guide groove could be dirty, or the oil-pump adjusting screw may be incorrectly adjusted. Fill the oil tank, clean the oil guide groove, and adjust the oil-pump screw.

Summary

Safety Precautions for Makita Chainsaws

General Safety Rules

Personal Protective Equipment

Details mandatory personal protective equipment (PPE) for safe chainsaw operation.

Fuel and Refuelling Safety

Kickback Prevention

Warns about kickback hazards and provides rules to prevent them during sawing.

Safe Operating Techniques

Putting into Operation

Guide Bar and Chain Installation

Step-by-step guide for installing the guide bar and saw chain onto the chainsaw body.

Chain Tensioning and Adjustment

Special Guide Bar Systems

Chain Brake Operation

Describes the function, engagement, and release of the chainsaw's chain brake mechanism.

Fueling and Lubrication

Covers fuel requirements, mixing, storage, and chain oil system operation.

Engine Starting and Stopping

Details the procedures for cold starting, warm starting, and stopping the chainsaw engine.

Carburetor and Brake Checks

Maintenance Procedures

Sharpening the Saw Chain

Replacing Parts

Periodic Maintenance Schedule

Service, Support, and Compliance

Troubleshooting Common Issues

Provides solutions for common malfunctions and problems encountered during chainsaw operation.

Makita EA3502S Specifications

General IconGeneral
BrandMakita
ModelEA3502S
CategoryChainsaw
LanguageEnglish

Related product manuals