EasyManua.ls Logo

Makita EA3500SRDB - User Manual

Makita EA3500SRDB
136 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Operators and Safety Manual
for Gasoline Chain Saws
Manuel d’emploi et de sécurité
de tronçonneuses thermiques
Manual de empleo y de seguridad
para motosierras
WARNING! Read and understand this Manual. Always follow safety precautions in the Operator’s and Safety
Manual. Improper use can cause serious injury! Preserve this Manual carefully!
WARNING! FUELS WITH MORE THAN 10% ETHANOL ARE NOT APPROVED FOR USE IN MAKITA 2-STROKE
ENGINES! Use of alternative fuels, such as E-20 (20% ethanol), E-85 (85% ethanol) or any fuels not meeting MAKITA
requirements are not approved for use in MAKITA 2-stroke gasoline engines!
USE OF ALTERNATIVE FUELS CAN CAUSE THE FOLLOWING PROBLEMS: Poor engine performance, loss of
power, overheating, fuel vapor lock, improper clutch engagement, premature deterioration of fuel lines, premature
deterioration of gaskets, premature deterioration of carburetors. USING ALTERNATIVE FUELS AND/OR 2-STROKE
OILS NOT ACCORDING TO JASO FC OR ISO-L-EGD IN MAKITA 2-STROKE ENGINES WILL VOID YOUR ENGINE
WARRANTY!
AVERTISSEMENT! Suivez toujours les conseils de sécurité du présent manuel d’emploi et de sécurité. Une
utilisation incorrecte de la tronçonneuse peut entraîner des blessures graves! Lisez et comprenez ce manuel.
Conservez avec soin ce manuel!
AVERTISSEMENT! LES CARBURANTS CONTENANT PLUS DE 10 % D’ÉTHANOL NE SONT PAS AUTORISÉS
POUR L’UTILISATION DANS LES MOTEURS 2 TEMPS! Les carburants alternatifs, tels que E-20 (20 % d’éthanol),
E-85 (85 % d’éthanol) ou tout autre carburant n’étant pas conformes aux exigences MAKITA ne sont pas autorisés
pour l’utilisation dans les moteurs essence à 2 temps MAKITA!
L’UTILISATION DE CARBURANTS ALTERNATIFS PEUT CAUSER LES PROBLÈMES SUIVANTS: Faible performance
moteur, Perte de puissance, Surchauffe, Bouchons de vapeur dans la conduite d’essence, Embrayage incorrect,
Détérioration prématurée des conduites d’essence, Détérioration prématurée des joints d’étanchéité, Détérioration
prématurée des carburateurs. L’UTILISATION DE CARBURANTS ALTERNATIFS ET/OU D’HUILES 2 TEMPS NON-
CONFORMES À LA NORME JASO FC OU ISO-L-EGD DANS LES MOTEURS À 2 TEMPS MAKITA ANNULERA VOTRE
GARANTIE MOTEUR!
¡ADVERTENCIA! Observe siempre las instrucciones de seguridad contenidas en el manual. Lea y compenétrese
con el contenido del manual. El uso inadecuado de la motosierra puede causar lesiones de gravedad.
Conserve este manual cuidadosamente.
¡ADVERTENCIA! ¡NO SE AUTORIZAN LOS COMBUSTIBLES CON MÁS DEL 10% DE ETANOL PARA SU USO EN
LOS MOTORES DE 2-TIEMPOS MAKITA! ¡El uso de combustibles alternativos, como el E-20 (20% de etanol), E-85
(85% de etanol) o cualquier otro combustible que no cumplan los requisitos de MAKITA no están autorizados para
su uso en motores de gasolina de 2-tiempos MAKITA!
EL USO DE COMBUSTIBLES ALTERNATIVOS PUEDE CAUSAR LOS SIGUIENTES PROBLEMAS: Pobre rendimiento
del motor, Pérdida del potencia, Sobrecalentamiento, Formación de burbujas de vapor en la tubería del
combustible, Acople inadecuado del embrague, Deterioro prematuro de las tuberías de combustible, Deterioro
prematuro de la juntas, Deterioro prematuro del carburador. EL USO DE COMBUSTIBLES ALTERNATIVOS Y DE
ACEITES PARA MOTORES DE 2-TIEMPOS DISTINTOS DE LOS DE LA NORMA JASO FC O ISO-L-EGD EN EN LOS
MOTORES DE 2-TIEMPOS MAKITA ANULARÁ LA GARANTIA DEL MOTOR.
EA3500S
EA3501S

Table of Contents

Questions and Answers

  • K
    knightnicholasSep 16, 2025
    Why is my Makita Chainsaw having warm start difficulties?
    • R
      robertsjaclynSep 16, 2025
      If you're experiencing warm start difficulties with your Makita Chainsaw, it could be due to a wrong carburetor adjustment. Adjust the carburetor to the correct settings.
  • C
    campbelljenniferAug 25, 2025
    Why is my Makita EA3500SRDB Chainsaw engine not starting?
    • A
      Ashley WardAug 26, 2025
      There could be several reasons why your Makita Chainsaw engine isn't starting. It could be due to a malfunction in the fuel supply or compression system, or a mechanical issue. Check the ignition spark and ensure the fuel tank is full. Also, inspect the STOP switch and wiring for any faults. Other potential causes include a defective carburetor, a dirty suction head, a bent or interrupted fuel line, defective cylinder base packing ring or piston rings, or broken parts in the starter or engine. Examine the cylinder base packing and piston rings. Inspect the starter spring and the engine for broken parts.
  • O
    oscar60Aug 26, 2025
    Why won't my Makita EA3500SRDB engine start?
    • C
      cochranmonicaAug 27, 2025
      If your Makita Chainsaw engine is not starting, several factors could be at play. There may be a malfunction in the fuel supply, compression, or mechanical systems. Check and repair the ignition system, fuel supply, or starter as needed. Also, ensure the STOP switch is in the correct position and check the wiring, spark plug cap, and spark plug. Inspect and adjust the combination switch; clean or replace the carburetor and suction head; and check the fuel line. Replace any defective parts in the cylinder or piston. Finally, inspect and replace the starter spring or any broken parts inside the engine.
  • D
    David ScottAug 27, 2025
    Why my Makita EA3500SRDB Chainsaw engine does not start?
    • C
      Cassandra DavisAug 27, 2025
      If your Makita Chainsaw engine is not starting, begin by checking the ignition spark. Also inspect the wiring, and replace the spark plug or cap if defective. Ensure proper spark plug sealing. Adjust the combination switch and clean the carburetor if the combination switch is in Choke position, or if the carburetor is defective, or the suction head is dirty, or the fuel line is bent or interrupted. Finally, inspect the starter and engine parts, and replace defective components if the cylinder base packing ring or radial shaft packings are defective, or if the cylinder or piston rings are defective.
  • D
    Donna LawrenceSep 17, 2025
    How to fix warm start difficulties on my Makita EA3500SRDB?
    • R
      Rebecca ArnoldSep 17, 2025
      If you're experiencing difficulties starting your Makita Chainsaw when it's warm, it could be due to an incorrect carburetor adjustment. To fix this, adjust the carburetor accordingly.
  • D
    Deborah GravesNov 22, 2025
    Why won't my Makita Saw start?
    • Z
      Zachary CallahanNov 22, 2025
      If your Makita Saw engine isn't starting easily, it could be due to several issues within the fuel supply, compression, or mechanical components. Check for a malfunctioning fuel supply system, compression system, or mechanical malfunction. Also, inspect if the stop switch is in the wrong position, or there's a fault or short-circuit in the wiring. A defective spark plug cap or spark plug could also be the cause. Other potential problems include the combination switch being in the choke position, a defective carburetor, a dirty suction head, a bent or interrupted fuel line, a defective cylinder base packing ring or radial shaft packings, defective cylinder or piston rings, a spark plug that doesn't seal, a broken spring in the starter, or broken parts inside the engine. Inspect and repair t...
  • Q
    qrobinsonSep 8, 2025
    What to do if Makita EA3500SRDB has insufficient power?
    • T
      Timothy WhiteSep 8, 2025
      If your Makita Chainsaw has insufficient power, it could be due to a dirty air filter, wrong carburetor adjustment, clogged muffler, clogged exhaust channel in the cylinder, or a clogged spark arrester screen. You should clean or replace the air filter and muffler, adjust the carburetor, and clear the exhaust channels.
  • B
    brittanypowellSep 9, 2025
    What to do if Makita EA3500SRDB Chainsaw has no chain lubrication?
    • J
      Jordan NguyenSep 10, 2025
      If your Makita Chainsaw isn't lubricating the chain, the oil tank might be empty, the oil guide groove could be dirty, or the oil pump adjusting screw might be incorrectly adjusted. Fill the oil tank, clean the oil guide groove, and adjust the oil pump.
  • A
    Andrew ChristianSep 3, 2025
    Why is my Makita Chainsaw chain not running?
    • K
      karenmaddenSep 3, 2025
      If the chain on your Makita Chainsaw isn't running, the chain brake might be activated. Check if the chain brake is in the 'off' position.
  • C
    Carolyn BartlettSep 1, 2025
    What to do if my Makita EA3500SRDB Chainsaw engine starts, but dies immediately?
    • M
      moorestephanieSep 1, 2025
      If your Makita Chainsaw engine starts but dies immediately, the idling adjustment might be wrong, or the suction head or carburetor could be dirty. Check and adjust the idling settings and clean the suction head or carburetor. Another possibility is a defective tank vent, an interrupted fuel line, a defective cable, or a defective combination switch. Inspect the tank vent and ensure the fuel line is not interrupted.

Makita EA3500SRDB Specifications

General IconGeneral
Power Output1.5 kW
Bar Length35 cm
Chain Pitch3/8"
Chain Gauge1.3 mm
Fuel Tank Capacity0.4 L

Related product manuals