Malsch Impulse 400 - User Manual

Questions and Answers

C
Colton HornAug 9, 2025
How to fix Malsch Impulse 400 motors that won't operate with the hand controller?
- C
  Chase EvansAug 9, 2025
  If the motors on your Malsch Medical Equipment aren't operating via the hand controller, here are a few things to check: * Ensure the mains cable is properly plugged in and the socket is live. * Verify the cabling plug connection to both the motor and hand controller. * For ICS control, make sure the mains cut-off is activated by pressing the green button. * Confirm that the functions on the hand controller are not locked. * Check for any obstructions in the adjustment area and remove them. If these steps don't resolve the issue, the hand controller or motor might be faulty, and you should inform the operator, retailer, or Betten Malsch GmbH.
E
Elizabeth SinghAug 14, 2025
What to do if opposite function activates on Malsch Impulse 400 Medical Equipment?
- S
  stephaniehuangAug 15, 2025
  If you find that the opposite function activates when you press the buttons on the hand controller of your Malsch Medical Equipment, it's likely that the motor plugs are mixed up. Check the correct cables or inform your operator, retailer or Betten Malsch GmbH.
J
James NelsonAug 20, 2025
Why do motors cut out on Malsch Impulse 400 Medical Equipment?
- S
  Stephanie Rogers MDAug 20, 2025
  If the motors on your Malsch Medical Equipment cut out after running for a while, it's possible the system has overheated. This can happen if the adjustment time or safe working load has been exceeded. To resolve this, allow the motor system to cool down properly.
M
mary52Aug 27, 2025
What to do if side rails can no longer be set up properly on Malsch Impulse 400 Medical Equipment?
- T
  Tiffany MillerAug 27, 2025
  If the side rails on your Malsch Medical Equipment can no longer be set up properly, there might be an obstruction or bend in the mechanism. Check all moving parts and remove any obstructions, or contact our customer service team.
F
Felicia SchneiderSep 1, 2025
How to remove obstructions from Malsch Impulse 400 Medical Equipment castors?
- M
  Melissa WeeksSep 2, 2025
  If you find obstructions in the castors of your Malsch Medical Equipment, remove them.

Summary

THE PRODUCTS

SPECIFIC FUNCTION

PICTOGRAMS;SYMBOLS

SAFETY INSTRUCTIONS

TECHNICAL DATA

Low voltage drive system

Technical specifications for the low voltage drive system (SMPS).

RATING PLATE

SYMBOLS ON THE HAND CONTROLLER FOR LOW VOLTAGE SYSTEM

Locking function

FUNCTIONS

Split side rail

Detailed description and diagram of the split side rail.

Back rest

How to adjust the back rest using the hand controller.

Release mechanism of the Back rest;CPR (optional)

Procedure for releasing and engaging the back rest mechanism.

Upper leg section

How to adjust the upper leg section using the hand controller.

Height adjustment

How to adjust the bed's height using the hand controller.

Transfer position

Low position;fall prevention

Comfort sitting position

Auto contour

Trendelenburg;anti-Trendelenburg position

Hand controller locking function

How to lock and unlock hand controller functions.

BRAKING AND MOVING

SIDE RAIL ADJUSTMENT

Full length side rail

How to raise and lower the full length side rail.

Split side rail GS

Split side rails VGS

DELIVERY AND ASSEMBLY

TROUBLESHOOTING

PRODUCT SAFETY

CLEANING AND DISINFECTION

Disinfection

MAINTENANCE

WARRANTY AND SERVICE

Malsch Impulse 400 Specifications

General

Category	Medical Equipment
Pulse Modes	Single, Continuous, Burst
Manufacturer	Malsch
Protection Class	I
Frequency	1-21 Hz
Applicators	15 mm
Display	Touchscreen
Programs	Preset protocols and user-defined programs
Energy Levels	Adjustable
Power Supply	AC 100-240V, 50/60Hz
Operating Temperature	+10°C to +30°C
Relative Humidity	30% to 75% (non-condensing)

Related product manuals

Malsch Impulse Series

36 pages