English
15
Program edit
This procedure allows you to record tracks in any desired order while
fitting the tracks into a specified tape length.
1. Program tracks according to the programming procedure in section
“PROGRAM PLAY” (page 11).
2. The rest of the program edit procedure is the same as step 1 to 8 in
the simple edit procedure.
Delete program edit
When recording from a disc to a tape, this procedure allows you to omit
the tracks you do not want to record, while fitting the tracks into a
specified tape length.
1. Program tracks according to the “delete programming” procedure in
the “PROGRAM PLAY” section (page 12).
2. The rest of the delete program edit procedure is the same as step 1
to 8 in the simple edit procedure.
NOTES
• As a CD may contain several peaks, a different peak may be found
every time the auto peak level search operation is performed.
• During simple edit play, program edit play and delete program edit
play operations other than the STOP, OPEN/CLOSE, VOLUME,
RECALL and TIME control operations are defeated. This is in-
tended to prevent mistakes in recording due to erroneous opera-
tion.
• The display is always in the time display mode during edit play. It is
not possible to switch to the text display mode.
Synchro Recording
This function starts the recording of the cassette deck automatically in
synchronism with the start of edit play of the CD player.
– Synchro recording can be started only when a Marantz autoreverse
cassette deck (ex. SD4050, SD555 etc.) with synchro recording
compatibility is connected to the CD player.
– Synchro recording is performed through the remote line connection
(rear panel jacks).
1. Set up the cassette deck for synchro recording. For the detailed
operations, please refer to the User Guide of the cassette deck.
2. When the pause button of the CD player is pressed to start the edit play
for tape side A, the cassette deck also starts automatically.
NOTE
When a tape with shorter length than the set tape recording time, the
CD player stops playback of tracks assigned for tape side A at the
moment recording of side A has completed. When recording of tape
side B starts, the CD player also starts playback of the tracks assigned
for side B.
CD-TEXT information display
The text information on CD-TEXT discs is displayed in the order shown
below each time the CD-TEXT button on the remote control unit is
pressed.
However that the included information differs from disc to disc,
so not all this information will necessarily be displayed. With this set,
items for which no text information is recorded on the disc are automati-
cally skipped.
The displayed text can be scrolled by pressing the
SCROLL/(RECALL)
button.
• During playback
The displayed information switches in the order below each time the
CD-TEXT
button is pressed. During playback, most of the displayed
information is for the currently playing track.
• In the stop mode
The displayed information switches in the order below each time the
CD-TEXT
button is pressed.
Title of currently playing track
fl
Album Title (album title)
fl
xx Title (title of track number xx)
fl
xx Artist (artist of track number xx)
fl
xx Songwriter (songwriter of track number xx)
fl
xx Composer (composer of track number xx)
fl
xx Arranger (arranger of track number xx)
fl
xx Message (message for track number xx)
fl
Disc ID (album identification number)
fl
Genre (album’s music category)
fl
xx Info. End (end of information for track number xx)
Album Title
fl
Album Title (album title)
fl
-- Title (title of -- track)
fl
Artist (album’s artist)
fl
-- Artist (artist of -- track)
fl
Songwriter (album’s songwriter)
fl
-- Songwriter (songwriter of -- track)
fl
Composer (album’s composer)
fl
-- Composer (composer of -- track)
fl
Arranger (album’s arranger)
fl
-- Arranger (arranger of -- track)
fl
Message (album’s message)
fl
-- Message (message for -- track)
fl
Disc ID (album identification number)
fl
Genre (album’s music category)
fl
All Info. End (end of all text information)
To Next Page
Loading...
