Marantz RC2000MKII - Rewriting Status Name; Rewriting DIRECT Function Button Names

1615
2. Place the laser disc player’s supplied infrared remote
controller so that its transmitter window is facing the
infrared sensor window of the RC2000 Mk w about 5
cm (2 inches) apart.
3. Press the LD function button o on the RC2000 Mk w.
4. Using the direct function page keys  and  i, set
the direct function to Page 1. Press the D-1 button u
on the RC2000 Mk w. At this point, both the LEARN
and NAME indicators will flash.
5. Press and hold the corresponding SIDE-A button on
the laser disc player’s remote transmitter until the “OK”
indicator appears in the RC2000 Mk w LCD window.
If the AGAIN indicator lights, it means that for some
reason, the command was not learned. Try steps 3, 4
and 5 again.
Renaming DIRECT keys during programming
At this point you have taught the function, now it is time to
rename. The remote will switch to the RENAME mode
automatically after teaching the command. This is indicated
by the left side of the D1 indicator blinking, meaning that
you can re-write that character.
If you wish to skip re-writing, press the OK button within the
cursor keys or other keys except ten keys.
6. Choose the desired letter or number by pressing the
10 numeric keypad buttons. Each button has various
characters assigned to it as follows:
7. Using the  or  cursor buttons will choose the
position to overwrite.
8. Continuing along, rewrite the characters. After
completion, press the OK button in the middle of the
cursor buttons.
9. Now, proceed to program the other commands from
the laser disc player’s remote transmitter to the other
DIRECT function buttons (D2-D8).
10. When you have “taught” all 8 direct functions for Page
1, press the page direction key  i to go to Page 2,
and you can program more direct function keys.
11. After memorizing all codes to all DIRECT function
buttons, press the operation mode button q with the
pen tip and return the RC2000 Mk w to the USE mode.
Now, the newly memorized codes are usable from the
RC2000 Mk w.
If you wish, you can re-write the names for each
function name, status name, and the direct
function as follows:
For our example, you can change the LCD display window
indication from “LD” to “LV-520” (which is the model
number for a Marantz laser disc player). Remember that
you can re-name a function selector button with a new
name of up to six characters of letters and numbers in any
combination.
MACRO MACRO
RC2000MK
LEARNING REMOTE CONTROL
POWER
ON OFF
ON/OFF
CLONE MACRO MODE
SOURCE
Press the MODE button to switch to USE.
MD
VCRDVDLDTV
1
OSD GUIDE MUTE
VOLCH
AMPAUXTAPECDTUNER
2 3
4 5 6 7 8 9
M 0 C
OK
Approx. 5 cm (2 inches)
LD remote control unit RC2000 Mk
ww
DSS
MD
VCRDVDLDTV
AMPAUXTAPECDTUNER
24
RC-5
USE
LEARN
NAME
D1
D2
D3
D5
D6
D7
E
V
E
R
S
E
F
O
R
W
A
R
AB
DISC SIDE
SCAN / CTRL
D-LEVEL
CTRL
Press and hold the SIDE-A button of the LD remote.
Press the D1 button.
1
2
3
4
5
6
7
8
9
0
1
2
3
4
5
6
7
8
9
0
A
D
G
J
M
P
S
V
Y
B
E
H
K
N
Q
T
W
Z
C
F
I
L
O
R
U
X
/
10 Numeric
Keypad
Toggles between...

SPACE
,
’