Marantz SD-60 - Playback and Recording Operations; Source;Tape Monitoring; Memory and Counter Functions; Playback and Quick Music Search

@2) SOURCE/TAPE switch
When recording or adjusting the recording level, press this
switch so that the SOURCE indicator lights. When adjusting
the recording level, the sound to be recorded can be
monitored. During recording, the source sound can be
monitored with the switch in the SOURCE position and the
just recorded sound can be monitored with the switch in
the TAPE position. During playback, this switch is auto-
matically set to the TAPE position to allow listening to the
tape sound and the TAPE indicator lights.
@3) M (memory) CALL BUTTON
The peak recording level is automatically stored in the
memory of this cassette deck. The peak level of the last
recording can be recalled and the peak level flashes for
about 5 seconds by pressing this button.
PHONES LEVEL contro!
Used to adjust the volume level of the headphones plugged
in the PHONES jack. To increase the volume level, turn this
control clockwise. To decrease the volume level, turn it
counterclockwise.
@5) PHONES JACK
Accepts headphones (optional) utilizing a standard stereo
phone plug.
COUNTER OPERATION BUTTONS
MEMO:
This button is used to store the current tape location in
memory. Storing the current tape location is useful when it
is desired to listen to the current selections repeatedly.
After pressing this button, play a selection. When play is
completed, press the <4 button to rewind or >> to fast-
forward the tape. The tape is then rewound to the position
stored in memory and stops. When the MEMO button is
pressed several times the tape location at the time it is
pressed last is stored in memory.
RESET:
Press this button to reset the counter reading to “0000” or
play time to “00.00”.
MODE:
To select the counter or time display, press this button.
Each time this button is pressed, display changes between
counter and time mode alternately.
@?) CASSETTE COMPARTMENT
PLAYBACK
1. Press the POWER switch to ON.
2.
Press
the
EJECT
button
to
open
the
cassette
compart-
ment.
3.
Load
a
cassette
tape
and
close
the
cassette
compart-
ment.
4.
When
the
tape
has
been
recorded
using
Dolby
NR,
select
the
same
Dolby
NR
setting
as
was
used
in
record-
ing.
5.
Select
the
counter
mode
with
the
COUNTER
MODE
button
and
reset
the
counter
reading
with
the
COUNTER
RESET
button.
6. Press the PLAY button.
Quick music search
With
the
quick
music
search
function,
a
selection
located
up
to
15
selections
after
or
before
that
which
you
are
now
listening
to
or
stopped
at
can
be
played
back.
Example:
For
listening
to
the
selection
located
10
selections
after
the current one:
1.
Press
the
QMS
button
10
times.
“P-10”
appears
on
the
display.
2. Press the > button.
The
tape
will
be
fast
forwarded
to
the
beginning
of
the
specified selection, and play starts automatically.
@
The
quick
music
search
function
operates
by
searching
for
blank
sections
on
the
tape.
Therefore,
to
play
back
the
selection
located
10
selections
before
the
current
one,
press
the
QMS
button
11
times
and
press
the
44
button.
When
the
QMS
button
is
pressed
10
times,
the
selection
located
9
selection
before
the
current
one.
RECORDING
1. Press the POWER switch to ON.
2.
Press
the
EJECT
button
to
open
the
cassette
compart-
ment.
3.
Load
a
cassette
tape
and
close
the
cassette
compart-
ment.
4.
Select
the
Dolby
NR,
HX
PRO
system
if
necessary.
*When
recording
an
FM
broadcast
with
Doiby
NR,
press the MPX-F button.
5.
Select
the
counter
mode
with
the
COUNTER
MODE
button
and
reset
the
counter
with
the
COUNTER
RESET
button.
6.
Adjust
the
bias
and
recording
signal
levels
to
align
with
the
characteristics
of
the
cassette
to
be
used.
Refer
to
the
descriptions
of
the
BIAS
and
CALIBRATION
controls.
7. Adjust the recording level.
1)
Press
the
REC
button
to
engage
the
rec
pause
mode,
and
play
a
selection
of
the
program
to
be
recorded.
The
REC
indicator
flickers
to
indicate
the
rec
pause
mode.
2)
Watch
the
peak
level
meters
and
adjust
the
REC
LEVEL
control
to
keep
the
meter
reading
from
going
higher
than
the
optimum
level
indicator
adjusting
the
REC
LEVEL
control.
8.
Reset
the
source
to
be
recorded
back
to
the
beginning.
Press
the
PLAY
section
or
PAUSE
button
to
begin
recording
and
immediately
begin
playing
the
source.
To
temporarily
stop
the
recording,
press
the
PAUSE
button.
To
resume
recording,
press
the
PLAY
section
or
PAUSE
button.