Need help?Do you have a question about the Marshall Amplification 5005 and is the answer not in the manual?
General| Channels | 1 |
|---|---|
| Inputs | 1x 1/4" Jack |
| Outputs | 1x 1/4" Jack |
| Output Power | 12 Watts |
| Type | Solid State Combo Amplifier |
| Controls | Volume, Bass, Treble |
| EQ | Bass, Treble |
Controls total mains power to the amplifier.
Controls H.T. supply to amp valves, keeps filaments heated during breaks.
Connects instrument to amplifier, top input for high power.
Connects instrument to amplifier, top input for high gain, treble boosted.
Controls the overall output level of channel 2.
Controls the overall output level of channel 1.
Controls the high frequency content of the amplifier.
Controls the middle register of the amplifier.
Controls the low frequency content of the amplifier.
Boosts upper frequencies for crispness and liveliness.
Controls total mains power to the amplifier.
Controls H.T. supply to amp valves during breaks.
Connects instrument to amplifier; high input for more volume.
Controls pre-amp level for overdrive amount.
Controls the overall output level of the amplifier.
Controls the high frequency content of the amplifier.
Controls the middle register; modifies treble/bass at high levels.
Controls the low frequencies of the amplifier.
Boosts upper frequencies for crispness and liveliness.
Provides protection for the high tension circuit.
Provides protection for the mains input circuit.
Connects amplifier to the mains power supply.
Matches amplifier output transformer to incoming mains voltage.
Matches output transformer impedance to loudspeaker load impedance.
Parallel jacks for connecting loudspeakers; impedance must be matched.
Low level output for recording, P.A. mixing, or slave systems.
Diagram and instructions for connecting multiple amplifiers.
Details input sensitivity for Channel 1 and 2, and bottom inputs.
Specifies typical power output at clipping and 10% distortion.
Describes frequency response and tone control characteristics.
Lists mains input, consumption, and fuse values.
Details pre-amp and output valves used in the amplifier.
Details input sensitivity for Channel 1 and 2, and bottom inputs.
Specifies typical power output at clipping and 10% distortion.
Describes frequency response and tone control characteristics.
Lists mains input, consumption, and fuse values.
Details pre-amp and output valves used in the amplifier.
Details low and high sensitivity input specifications.
Specifies typical power output at clipping and 10% distortion.
Describes frequency response and tone control characteristics.
Lists mains input, consumption, and fuse values.
Details pre-amp and output valves used in the amplifier.
Details low and high sensitivity input specifications.
Specifies typical power output at clipping and 10% distortion.
Describes frequency response and tone control characteristics.
Lists mains input, consumption, and fuse values.
Details pre-amp and output valves used in the amplifier.
Connects instrument to amplifier (high powered input).
Connects instrument to amplifier (low powered input).
Controls pre-amplification level for overdrive or clean sound.
Controls the overall output level of the amplifier.
Controls the high frequency content of the amplifier.
Controls the middle register of the amplifier.
Controls the low frequencies of the amplifier.
Boosts upper frequencies for crispness and liveliness (not on 5002/5005).
Low level output for recording, P.A. mixing, or outboard systems.
Output for headphones; mutes internal loudspeaker.
On/off switch for mains power to the amplifier.
Details low and high sensitivity input values.
Describes tone control characteristics for Treble, Middle, and Bass.
Specifies loudspeaker and H.P./Line-out output details.
Details internal power supply voltage and current rating.
Specifies fuse values for 120v and 220/240v mains.
Details low and high sensitivity input values.
Describes tone control characteristics for Treble, Middle, and Bass.
Specifies loudspeaker and H.P./Line-out output details.
Details internal power supply voltage and current rating.
Specifies fuse values for 120v and 220/240v mains.
Details sensitivity and maximum input level.
Describes tone control characteristics for Bass, Middle, and Treble.
Specifies power output and construction type.
Details the specially designed 12 inch loudspeaker.
Lists mains input voltage and power consumption.
Specifies headphone output power.
Specifies D.I. output level.
Connects instrument to the amplifier.
Controls pre-amplification level for overdrive or clean sound.
Controls the overall output level of the amplifier.
Controls the high frequency content of the amplifier.
Controls the middle register of the amplifier.
Controls the low frequencies of the amplifier.
Controls the depth of the reverb effect.
Low level version of the amplifier output.
Output for headphones; mutes internal loudspeaker.
On/Off switch for mains power to the amplifier.
Connects instrument to the amplifier.
Controls pre-amplification level for overdrive or clean sound.
Controls the overall output level of the amplifier.
Controls the high frequency content of the amplifier.
Controls the middle register of the amplifier.
Controls the low frequencies of the amplifier.
Boosts upper frequencies for crispness and liveliness.
Controls the depth of the reverb effect.
Output for stereo headphones; mutes internal loudspeaker.
Low level output for recording, P.A. mixing, or slave systems.
On/Off switch for mains power to the amplifier.
Connects instrument to the amplifier.
Controls input level for overdrive or clean sound.
Controls the high frequency content of the amplifier.
Controls the mid range of the amplifier.
Controls the low frequencies of the amplifier.
Controls the overall volume level of the amplifier.
Controls H.T. supply to amp valves during breaks.
Controls total mains power to the amplifier.
Connects the amplifier to mains power supply.
Fuse for the mains input, value on back of amp.
XLR socket for balanced line output to external equipment.
Output for internal or external loudspeaker (8 ohm nominal).
Output for headphones, operative when speaker is disconnected.
Unbalanced line-out for connecting to outboard equipment.
Details sensitivity, overload level, and impedance.
Specifies power output at varying distortion levels.
Specifies headphone output power at clipping.
Specifies unbalanced line output level.
Specifies balanced XLR output characteristics.
Details signal-to-noise ratio for flat response and maximum sensitivity.
Describes the integral master volume circuit function.
Lists the pre-amp and power tubes used.
Details quiescent and clipping power consumption.
Describes the 12 inch Celestion driver.
Connects instrument to amplifier (high powered input).
Connects instrument to amplifier (low powered input).
Controls pre-amplification level for overdrive or clean sound.
Controls the overall output level of the amplifier.
Controls the high frequency content of the amplifier.
Controls the middle register of the amplifier.
Controls the low frequency content of the amplifier.
Low level output for recording, P.A. mixing, or outboard systems.
Output for headphones; mutes loudspeakers.
On/off switch for mains power to the amplifier.
Connects the amplifier to the mains power supply.
For connecting loudspeakers (not less than 8ohms).
List of essential safety guidelines for operating the equipment.
To Next Page