Marshall Amplification ACTON II Bluetooth

Questions and Answers:

L
Lisa HernandezAug 13, 2025
Why does my Marshall Amplification Speakers Bluetooth connection keep dropping out?
- J
  Jeffrey JamesAug 13, 2025
  If your Marshall Amplification Speakers Bluetooth connection drops out, it may be due to distance or obstructions. Try moving the devices closer, within 10 meters, and remove any obstacles like walls or doors. Electrical disturbances from microwave ovens, wireless network adapters, fluorescent lights, and gas cookers can also interfere. These items use the same frequency range as the Bluetooth device.
A
Amy NicholsonAug 17, 2025
What to do if my Marshall Amplification Speakers are not responding?
- J
  Jessica FrazierAug 17, 2025
  If your Marshall Amplification Acton II speaker isn't responding, a software issue might be the cause. To resolve this, unplug the speaker from the wall socket, wait 15 seconds, and then plug it back in.
L
Laurie RichardsonAug 20, 2025
How to fix no audio on Marshall Amplification Speakers?
- K
  kevinzhangAug 20, 2025
  If there is no audio or the audio is too low on your Marshall Amplification Speakers, ensure the correct audio source is selected and properly connected to the Acton II. Also, check the volume levels on both your audio source and the speaker, and increase them slightly if needed.
S
Sarah MoralesAug 25, 2025
Why can't I connect my Bluetooth device to my Marshall Amplification Speakers?
- D
  Dean HartAug 25, 2025
  If you are unable to connect or pair your Bluetooth device with your Marshall Amplification Speakers, first ensure that Bluetooth is enabled on your device. If two devices are already connected to the speaker, disconnect one before attempting to connect a new device. If needed, put the speaker into pairing mode by pushing and holding the Bluetooth button for 3 seconds to make it discoverable.
J
jacoblewisAug 28, 2025
What to do if the audio is distorted on Marshall Amplification Speakers?
- C
  Charles SantosAug 29, 2025
  If the audio from your Marshall Amplification Speakers is distorted, try the following: * Reduce the playback volume on your audio source. * Try using a different audio file or music player. * Lower the volume on the speaker itself. * Reduce the bass or treble settings on the speaker.
J
Judith GraySep 1, 2025
Why are my Marshall Amplification Speakers making a crackling sound?
- D
  Dr. Angela SmithSep 1, 2025
  If you hear a crackling sound from your Marshall Amplification Speakers, it means the amplifier is likely clipping because it's running out of output power. To fix this, decrease the volume on your audio source and also lower the volume or bass on the Acton II.
T
Tiffany FloydSep 4, 2025
How to turn on Marshall Amplification Speakers Acton II?
- M
  Matthew LeonSep 4, 2025
  If your Acton II Marshall Amplification Speakers do not turn on, ensure that the speaker is properly connected to a working mains electricity supply. Connect the mains lead to the Acton II and a functioning wall socket. Then, pull and hold the power lever towards the front of the speaker until the indicator lights illuminate.
R
rita25Sep 8, 2025
What causes erratic performance in Marshall Amplification Speakers?
- C
  Christina HernandezSep 8, 2025
  If your Marshall Amplification Acton II speaker is showing erratic performance, it might be due to interference from another electronic device. Try moving the Acton II to a different location or turning off or moving the interfering electronic device.

Marshall Amplification ACTON II Bluetooth Specifications

General

Type	Portable Bluetooth Speaker
Output Power	30 W
Adjustable Bass and Treble Controls	Yes
Stereo/Mono	Stereo
Mains Input Voltage	100-240 V
Mains Frequency	50/60 Hz
Waterproof	No
Frequency Response	50 Hz – 20 kHz
Bluetooth Range	10 m
Bluetooth Version	5.0
Power Amplifiers	One 30 W Class D amplifier for the woofer, Two 15 W Class D amplifiers for the tweeters
Inputs	3.5 mm