Marshall Amplification MG100FX

Jack input for your guitar. Use a good quality guitar cable.

Controls the amount of signal entering the pre-amp and distortion.

Selects between Clean (green) and Crunch (red) channels.

Adds warmth and low-end depth to your sound.

Selects between OD1 (green) and OD2 (red) channels.

Adjusting the middle frequencies will vary the amount of body in your sound.

Makes your sound brighter and more cutting, or softer.

Adds a lush reverb to the selected channel, from subtle to cavernous.

Controls the volume of the selected channel.

Matches delay FX time to the time between two pushes. Switches amp between manual and preset modes.

Selects and adjusts one of four effects: Chorus, Phaser, Flanger & Delay.

Stores current amp settings into the current channel or footcontroller. Lights red in manual mode.

Controls the master volume of the amplifier.

Connect your MP3, CD or tape player for practice.

1/4" Jack socket for the optional footcontroller.

For silent practice. Automatically mutes the internal speaker.

Turns your amplifier on and off. Channel switches light up when on.

Selects between Clean/Crunch and OD1/OD2 channels using dedicated switches.

Explains the two operating modes: Preset (factory default) and Manual.

Factory default mode where control positions are stored per channel (except Master Volume).

Amp settings match physical control positions. No presets recalled upon channel change.

Describes the amplifier's simultaneous Reverb and FX capabilities.

Details the FX section, which can be globally turned on/off via the FX switch.

Control for the delay effect amount. Setting to '0' switches the delay off.

Matches delay time to presses. LED flashes at selected delay time.

Allows connection of external audio sources for practice.

For silent practice. Mutes the unit's speaker when a jack is inserted.

Turns the amplifier on and off. Unstored settings are lost.

WARNING: Erases all user presets and replaces them with factory presets.

Technical specs for MG15FX: power, channels, speaker, weight, size.

Technical specs for MG30FX: power, channels, speaker, weight, size.

Jack input for your guitar. Use a good quality guitar cable.

Controls the amount of signal entering the pre-amp and distortion.

Selects between Clean (green) and Crunch (red) channels.

Adds warmth and low-end depth to your sound.

Selects between OD1 (green) and OD2 (red) channels.

Varies the amount of body in your sound.

Makes your sound brighter and more cutting, or softer.

Switches the reverb effect on and off.

Adds a lush reverb to the selected channel, from subtle to cavernous.

Controls the volume of the selected channel.

Switches the FX section (Modulation and Delay) on and off.

Selects and adjusts one of three modulation effects: Chorus, Phaser & Flanger.

Matches delay FX time to the time between two pushes. LED flashes at selected delay time.

Controls the amount of signal sent to the delay effect.

Switches the external FX Loop on and off.

Controls the master volume of the amplifier.

Switches power amp damping between classic and modern response.

3.5mm headphones output or Line Out for recording.

Stores amp settings into the current channel or footcontroller. Lights red in manual mode.

Turns the amplifier on and off. Unstored settings are lost.

Connects the detachable mains power lead. Check voltage compatibility.

Jack socket for the connection of the footcontroller.

Connects internal or external speakers. Ensure correct impedance.

Jam to your favourite MP3, CD or tape track.

Connect to the output of an external effects processor or pedal.

Connect to the input of an external effects processor or pedal.

Specifications for the MG50FX Combo: power, channels, speaker, weight, size.

Specifications for the MG100FX 1x12" Combo: power, channels, speaker, weight, size.

Specifications for the MG100FX 2x12" Combo: power, channels, speaker, weight, size.

Specifications for the MG100HFX Head: power, channels, speaker, weight, size.

Selects between Clean/Crunch and OD1/OD2 channels using dedicated switches.

Explains the two operating modes: Preset (factory default) and Manual.

Factory default mode where control positions are stored per channel (except Master Volume).

Amp settings match physical control positions. No presets recalled upon channel change.

Describes the amplifier's simultaneous Reverb, Delay, and Modulation capabilities.

Details the FX section, consisting of Delay and Modulation. FX switch controls both.

Control for the delay effect amount. Setting to '0' switches the delay off.

Control for modulation effects. Setting to '0' switches modulation off.

Matches delay time to presses. LED flashes at selected delay time.

Connects external audio sources for practice.

Provides headphones out or Line Out for silent recording.

Selects between two power amp damping modes (classic and modern).

Details the series FX loop for connecting external processors.

Guidance on connecting extension cabinets and impedance requirements.

Turns the amplifier on and off. Unstored settings are lost.

WARNING: Erases all user presets and replaces them with factory presets.

Each footswitch can be assigned a different stored function.

Reflects the current status of the amplifier or tuner details.

Indicates the various functions of the footcontroller.

Details the default factory assignments for the footswitches.

Explains how to program footswitches for switches or presets.

Assigns a front panel switch to a footswitch.

Assigns a complete preset to a footswitch.

Explains what the digital display shows for presets and channel changes.

Accessing and using the built-in tuner via front panel or footswitch.

Describes the 'Clean' factory preset with specific control settings.

Describes the 'Crunch' factory preset with specific control settings.

Describes the 'OD1' factory preset with specific control settings.

Describes the 'OD2' factory preset with specific control settings.