Marvel 30iM - Installation: Drain Plumbing

Illus. No. Description Qty. Req. Part No. Service Assembly
1 Condenser 1 41003609 42243035
2 Pop Rivet, Steel 4 41003962 42243035
3 Coil Retainer 1 41003662 42241490
4 Solenoid Coil 1 41003601 42242141
5 Hot Gas Valve 1 41003914 42242020
6 Drier Assembly 1 42102389 42242961
7 Speed Nut 1 41000153 42244701
8A Fan Shroud 1 41006282 42244704
8B Fan Shroud, Outdoor 1 41008531 42245202
9 Fan Blade 1 41003616 42242015
10 Silencer, Spacer 1 M000101A 42244701
11 Locknut 5 41006874 42244701
12 Fan Motor Assembly 1 42183571 42244701
13 Carriage Bolt 5 1130006A 42244701
14 Carriage Bolt 2 08205050 42243194
15 Carriage Bolt 1 1130006A 42242900
16 Sleeve, Compressor 2 41008199 42243194
17 Grommet, Compressor 4 41008198 42243194
18 Locknut 1 41006874 42242900
19 Lock Washer 1 41005417 42242900
20 Ground Wire, Compressor 1 41001401 42242900
21 Lock Washer 1 08205116 42242900
22 Screw 1 08205200 42242900
23 Washer 2 08204877 42243194
24 Locknut 2 08205051 42243194
25 Compressor Assembly 1 41008182 42243194
26 Compressor PTC Starter 1 41008200 42244702
27A Back Panel 1 41009202 42242962
27B Back Panel, Outdoor 1 42104901 42245203
28 Power Cord Clamp 1 41006046 42242963
29 Locknut 1 41006874 42242963
30 Carriage Bolt 1 1130006A 42242963
31 Baseplate 1 41006276 42242964
32 Water Valve Assembly 1 42262644 42242965
33 Drain Valve 1 41005530 42242966
34 Screw 2 08204928 42242965
35 Screw 2 08204928 42242966
36 Tee Fitting/Flow Restrictor Assembly 1 42283196 42242967
37 Hose Clamp 4 41006769 42242967
38 Power Cord 1 41006733 42242963
39 Bracket, Saturn Control 1 44000580 42246367
40A Screw 24 08204928 42245416
40B Screw-Stainless Steel, Outdoor 24 41005076 42245203
41 Electronic Control, Saturn 1 41050002 42246366
42 Transformer 1 41005681 42242973
43 Screw 6 41005086 42242971
44 Terminal Block 1 41005078 42242971
45 U-Clip 1 41005945 42243015
46A Access panel assembly 1 41005943 42243016
46B Access panel assembly-Stainless Steel, Outdoor 1 41008533 42245204
47 Compressor Overload 1 41008201 42245580
* Power Wire Harness 1 41050001 42246383
* Not Shown
22
SERVICE PARTS LIST THREE
Drain Plumbing
Your ice machine uses a gravity drain, (figure 1)
that requires 5/8" I.D. tubing from the back of the
ice machine to a plumbed connection to a sanitary
sewer. Remove the access panel to plumb in drain
connection. Gravity drain location for built-in units
can be within the area shown in figure 3. An option-
al drain pump, (figure 2) can be purchased for your
ice machine if a gravity drain is not accessible.
OBSERVE AND FOLLOW ALL LOCAL CODES
WHEN INSTALLING ICE MACHINE.
5
INSTALLATION: DRAIN PLUMBING
figure 1
figure 2
figure 3
Gravity Drain Location
* With optional filler kit
FAILURE TO USE ADEQUATE DRAINAGE
SYSTEM WILL RESULT IN SURROUNDING
WATER DAMAGE AND/OR POOR ICE
PRODUCTION.