the ground for operations. This is awkward operating position that
the operator has to bring his face close to the machine, and thus
risks being struck by wood chips or debris.
Warning!
ELECTRICAL SAFETY
• To avoid the risk of electric shock from the power cable, we
strongly advise that the cable be plugged into a socket which
has RCD protection.
• Long power cables will cause a drop in voltage, impairing the
performance of the machine.
• Cables up to 10m long must have 2.5mm2 diameter.
• Ensure that the plug pins on the cable and the machine are not
bent, and that the weight of the cable will not pull the socket
apart.
• Do not separate the plug and socket by pulling on the cables.
• Check the condition of the power cable regularly for insulation
damage, replacing if necessary.
• Do not bypass the safety switch on the cleaning flap retaining
screw.
KEEP BYSTANDERS AND CHILDREN AWAY
The log splitter must be always operated by one
person only. Other people should keep a safe
distance from the work area, especially
when the log splitter is under operations. Only one
person at a time should try to free jammed logs.
INSPECT YOUR LOG
Make sure there are no nails or foreign objects in logs to be split.
The ends of the logs must be cut square. Branches must be cut of
flush with the trunk.
DON’T OVERREACH
Floor must not be slippery. Keep proper footing and balance at all
times. Never stand on log splitter. Serious injury could occur if the
tool is tipped or if the cutting tools is unintentionally contacted.
Do not store anything above or near the log splitter where anyone
might stand on the tool to reach them.
AVOID INJURY FROM UNEXPECTED ACCIDENT
Always pay full attention to the movement of the log
pusher. Do not attempt to load the log on until the log
pusher has stopped. Keep hands out of the way of all
moving parts.
PROTECT YOUR HANDS
Keep you hands away from splits and cracks which
open in the log; They may close suddenly and crush
or amputate your hands. Do not remove jammed logs
with you hands.
DON’T FORCE TOOL
It will do a better and safer job at its design rate. Never try to split
logs larger than those indicated in the specifications table. This
could be dangerous and may damage the machine. Don’t use log
splitter for a purpose for which it was not intended.
NEVER LEAVE TOOL RUNNING UNATTENDED
Don’t leave tool until it has come to a complete stop.
DISCONNECT POWER
Unplug when not in use, before freeing jammed logs,
making adjustments, changing parts, cleaning, or
working on the log splitter; Consult technical manual
before servicing.
PROTECT THE ENVIRONMENT
Take used oil to an authorised collection point or follow
the stipulations in the country where the log splitter is
used. Do not discharge into drains, soil or water.
MAINTAIN YOUR LOG SPLITTER WITH CARE
Keep the log splitter clean for best and safest performance.
MAKE THE WORKSHOP CHILDPROOF
Lock the shop. Disconnect master switches. Store the log splitter
away from children and others not qualified to use it. Children
should not use the machine.
Application Conditions
This log splitter is a home use model. It is designed for operating
under ambient temperatures between +5°C and 40°C and for
installation at altitudes no more than 1000m above M.S.L. The
surrounding humidity should less than 50% at 40°C. It can be
stored or transported under ambient temperatures between -25°C
and 55°C.
ELECTRICAL REQUIREMENTS
Connect the main leads to a standard 230V±10% (50HZ±1Hz)
electrical supply which has protection devices of under-voltage,
over-voltage, over-current as well as a residual current device (RCD)
which maximum residual current rated at 0.03A.
Contents of the Shipping Container
A. Log Splitter 1 set
B. Support Leg 1 pc
C. Owner’s Manual 1 pc
D. Loose Part Bag (containing) M8 Bolts & Nuts— 5 sets
Note: Hardware to mount this log splitter to a work bench is
NOT supplied.
To Next Page
Loading...
Need help?
General
