WARNING!
• Use the proper extension cord. Make sure to use an extension cord that is heavy enough to carry
the current required by the tool. An undersized cord will cause a drop in line voltage, resulting in
loss of power and overheating of the tool.
• Use the extension cord only for intended purpose. Do not pull the extension cord to remove it
from the power socket.
CAUTION!
In all cases, verify that the outlet in question is properly grounded. if you are not sure, have a
licensed electrician check the outlet.
model no. 055-4504-8 | contact us 1-800-689-9928
9
SAFETY GUIDELINES
8
SAFETY GUIDELINES
• BEFORE ATTACHING a workpiece to the faceplate, always rough it out to make it as rough as possible.
This minimizes vibrations while the piece is being turned. Always fasten the workpiece securely to the
faceplate. Failure to do so could result in the workpiece being thrown from the lathe.
• POSITION your hands so that they will not slip onto the workpiece.
• REMOVE all loose knots in the stock before mounting it between the centres or on the faceplate.
• DO NOT LEAVE A RUNNING LATHE UNATTENDED. Leave the work area only after the motor has come to
a full stop.
• HANG your turning tools on the wall beyond the tailstock end of the lathe. Do not lay them on the bench
so that you must reach over the revolving workpiece to select them.
• KEEP A FIRM HOLD and remain in control of the cutting tool at all times. Take special precautions when
shaping a section of stock in which knots or voids are found.
• COMPLETE the hand-sanding of all workpieces before removing them from the lathe.
USE SAFETY GOGGLES AND EAR PROTECTION:
ALWAYS WEAR EYE PROTECTION THAT CONFORMS WITH CUL REQUIREMENTS. FLYING
DEBRIS can cause permanent eye damage.
The tool is loud and the sound can cause hearing damage. Always wear ear protection to help
prevent hearing damage and loss. Failure to comply may result in moderate injury.
USE DUST MASK:
Some dust created by sawing contains chemicals that are known to cause cancer, birth defects
or other reproductive harm. Some examples of these chemicals come from lead-based paints,
crystalline silica from bricks, cement and other masonry products, arsenic and chromium from
chemically treated lumber. To reduce exposure to these chemicals, work in a well-ventilated
area with approved safety equipment, such as dust masks that are specially designed to filter out microscopic
particles.
ELECTRICAL SAFETY
GROUNDING INSTRUCTIONS:
In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current
to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding
conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed
and grounded in accordance with all local codes and ordinances.
Do not modify the plug provided. If it will not fit the outlet, have the proper outlet installed by a qualified
electrician.
Improper connection of the equipment-grounding conductor
can result in a risk of electric shock. The conductor with
a green outer surface, with or without yellow stripes, is the
equipment-grounding conductor. If repair or replacement
of the electric cord or plug is necessary, do not connect the
equipment-grounding conductor to a live terminal.
Check with a qualified electrician or service technician if
the grounding instructions are not completely understood,
or if in doubt as to whether the tool is properly grounded.
Use only three-wire extension cords that have three-prong
grounding plugs and three-pole receptacles that accept the
tool's plug, as shown in Fig. 1. Repair or replace a damaged or worn cord immediately.
GROUNDING INSTRUCTIONS:
• Make sure the extension cord is in good condition. When using an extension cord, be sure to use one
that is heavy enough to carry the current that your product will draw. An undersized cord will cause a
drop in line voltage, which will result in loss of power and overheating. The table on the next page shows
the correct size to be used according to cord length and nameplate ampere rating. When in doubt, use
the next heavier gauge. The smaller the gauge number, the heavier the cord.
• Make sure your extension cord is properly wired and in good condition. Always replace a damaged
extension cord, or have it repaired by a qualified person before using it. Protect your extension cords from
sharp objects, excessive heat, and damp or wet areas.
• Use a separate electrical circuit for your tools. This circuit must consist of not less than #12 wire with a
20 A time-delayed fuse or a #14 wire with a 15 A time-delayed fuse. Before connecting the motor to the
power line, make sure the switch is in the OFF position and the electric current is rated the same as the
current stamped on the motor nameplate. Running at a lower voltage will damage the motor.
Fig. 1
Three-prong plug
Grounding prong
Properly grounded outlet
To Next Page
Loading...
Need help?
General
