Matermacc IRRIGAMATIC PRO45 User Manual

Use and Maintenance Handbook
IRRIGAMATIC
PRO45 - PRO35
Matermacc S.p.A.
Via Gemona, 18 - 33078 - San Vito al Tagliamento (PN) ITALIA
Telefono +39 0434/85267 telefax +39 0434/85517 www.matermacc.it e-mail info@matermacc.it
Cod.58330261
Irrigamatic
PRO35
Irrigamatic
PRO45
Use and Maintenance
Handbook
Carefully read this Handbook before using

Matermacc IRRIGAMATIC PRO45 Specifications

General

Brand	Matermacc
Model	IRRIGAMATIC PRO45
Category	Desktop
Language	English

Summary

INTRODUCTION

UPDATING THE MANUAL

Describes how the manual reflects the equipment's state at sale and reserves the right to make changes.

COPYRIGHT

States ownership of manual content and restrictions on distribution without permission.

WARRANTY

WARRANTY DECLINE

Lists conditions under which the warranty is not valid.

NOTES ON SAFETY

OPERATIONAL SAFETY

Provides guidelines for safe operation and maintenance procedures.

RECYCLING AND PROCESSING

Advises on proper disposal of electrical and electronic devices.

GENERAL FEATURES

FUNCTIONS

Lists the main operational functions of the Irrigamatic PRO35-PRO45.

OPTIONALS

Details optional features available for the Irrigamatic system.

USER INTERFACE

INSTRUCTIONS FOR USE

START UP AND MAIN MENU

Guides through the initial power-on sequence and main menu navigation.

HOW TO ACCESS MENU

Explains the general procedure for accessing and navigating console menus.

PROGRAMMING AN IRRIGATION CYCLE

Outlines the parameters needed to set up an irrigation cycle.

PROGRAMMING EXAMPLE OF AN IRRIGATION (STANDARD)

Provides a step-by-step example of programming a standard irrigation cycle.

START DELAY PARAMETER

Details how to set the delay before irrigation begins.

END DELAY PARAMETER

Describes how to set the delay after irrigation ends.

PERFORMING THE IRRIGATION

Guides on initiating the irrigation cycle after parameter setup.

DURING THE IRRIGATION

Explains the display during an active irrigation cycle and parameter adjustments.

INTERRUPTING AND RESTARTING IRRIGATION

Details procedures for temporarily stopping and resuming irrigation.

MEASURING UNIT PARAMETERS

Covers setting measurement units, type registration, and nozzle parameters.

LANE WIDTH AND COMPUTED FLOW RATE

Explains setting lane width and viewing computed flow rate.

SECTOR CONFIGURATION

Details sector setup for PRO45, including speed and length.

IRRIGATION RUN END TIME

Guides on setting the irrigation end time and its effect on other parameters.

RETRIEVAL SPEED ADJUSTMENT

Describes how to check and adjust the retrieval speed during operation.

CALIBRATING THE MACHINE

Outlines the process for machine calibration, noting it's password-protected.

CALENDAR AND COUNTER SETTINGS

Guides on setting the date, time, and work counters.

WORK PARAMETERS

PASSWORD-PROTECTED USER PARAMETERS

Lists user-configurable parameters requiring a password.

ERROR MESSAGES

USING THE GSM/GPRS MODULE (OPTIONAL)

SIM CARD ASSEMBLY INSTRUCTIONS

Provides steps for installing the SIM card into the GSM/GPRS module.

MANAGING THE PHONEBOOK

Explains how to manage stored phone numbers via SMS commands.

PHONEBOOK MANAGEMENT

Covers deleting, enabling/disabling, and reading phonebook entries.

MACHINE STATUS QUERIES

Details SMS commands to query machine status and retrieval speed.

REMOTE MACHINE CONTROL

Explains commands for changing retrieval speed and remote start/stop.

SMS COMMAND REFERENCE

Provides a comprehensive list of SMS commands and their replies.

TEST PROCEDURE

SENSOR TESTS

Describes how to test the speed, work end, and unwinding end sensors.

SWITCH AND FLOW METER TESTS

Covers testing the pushure switch and flow meter inputs.

MOTOR AND SENSOR TESTS

Explains tests for motor functions and wind/rain sensor inputs.

AUXILIARY OUTPUT AND BATTERY TEST

Details tests for auxiliary outputs and battery status.

SYSTEM COMPONENT TESTS

Covers tests for clock, memory, GSM module, and final system check.