MAXDATA PLATINUM 500 I - User Manual

MAXDATA PLATINUM 500 I – Quick Start Guide
Safety
Thank you for buying a MAXDATA PLATINUM 500 I Server. This document describes how to set up
the system, turn on the system, and complete configuration for the system.
Installation and service
Installation and service of this product is to be performed only by qualified service
personnel to avoid risk of injury from electrical shock or energy hazard.
Enclosure cover
In order to comply with applicable safety, emission, and thermal requirements, no
covers should be removed and all bays must be fitted with drive carriers.
Battery Safety
There is a danger of explosion if the battery is incorrectly replaced.
Dispose of used batteries in accordance with the manufacturer’s instructions and
national regulations.
Warning Caution
Electrostatic discharge
Observe normal Electrostatic Discharge (ESD) procedures during system integration
to avoid possible damage to the server board and/or other components of the server
system.
Server system power
System power on/off: The power button DOES NOT turn off the system AC power. To
remove power from the server system, you must unplug the AC power cord from the
wall outlet or the chassis.
Safety instruction for upright system
To ensure stability, the floor stands must be turned outwards.
Site Selection
Technical Specifications
Dimensions (upright configuration):
- 444 mm high
- 222 mm wide
- 675 mm deep
- 36 kg max. weight
System power:
- Redundant power supply (two line connectors)
100–127 V/200–240 V at 50/60 Hz; 10 A/5 A max.
- Single power supply
100–127 V/200–240 V at 50/60 Hz; 10 A/5 A max.
Temperature range: +10 °C to +30 °C
The system is designed to operate in a typical office environment. Choose a site that is:
• Clean,dryandfreeofairborneparticles(otherthannormalroomdust).
• Well-ventilatedandawayfromsourcesofheatincludingdirectsunlightandradiators.
• Awayfromsourcesofvibrationorphysicalshock.
• Isolatedfromstrongelectromagneticeldsproducedbyelectricaldevices.
System Overview
Follow the link “User-Support und Treiber” on www.maxdata.de to access the download area and download a more detailed guide.
• Inregionsthataresusceptibletoelectricalstorms,werecommendyouplugyoursystemintoa
surge suppresser and disconnect telecommunication lines to your modem during an electrical
storm.
• Providedwithaproperlygroundedwalloutlet.
• Provided with sufcientspace to access the power supply cord(s) because theyserveasthe
product’s main power disconnect.
Regulatory Compliance
This product complies to the following requirements:
- EN 60950 – Safety
- EN 55022 – Emissions
- EN 55024 – Immunity
- EN 61000-3-2 – Harmonics
- EN 61000-3-3 – Voltage Flicker
- CE – EMC Directive 89/336/EEC
This product has a CE declaration of conformity (CENELEC Europe).
This server system is compliant to European Directive 2002/95/EC (RoHS).
Front Controls Back Panel Connectors
MAXDATA PLATINUM 500 I M8 – Quick Start Guide 1
A. Powerbutton
B. Reset button
C. Warningmutebutton
D. PowerLED
E. HDD LED
F. NIC2 LED
G. NIC1 LED
H. WarningLED
A. Serial port A
B. Video port
C. NIC 1 (top), two USB ports (bottom)
D. NIC 2 (top), two USB ports (bottom)
E. Diagnostic LEDs
F. ID LED
G. Status LED
A
C
E
B
D
F
G
H

Summary

Safety Information

General Safety Warnings

Covers installation, enclosure, battery, ESD, power handling, and upright system safety guidelines.

Site Selection and Preparation

Recommended Site Conditions

Details requirements for a clean, dry, well-ventilated environment, avoiding heat, vibration, and EMI.

Electrical Precautions

Advises on surge protection and disconnecting lines during electrical storms.

System Overview and Components

Technical Specifications

Provides details on system dimensions, weight, power supply, voltage, and operating temperature range.

Regulatory Compliance

Lists standards and directives the product complies with, including EN, CE, and RoHS.

Front Panel Controls

Identifies front panel buttons and LEDs for power, reset, warning, and status indicators.

Back Panel Connectors

Details rear panel connectors for serial, video, network, USB, and status indicators.

Server Board Layout and Storage

Component Locations Diagram

Visual guide to the placement of CPUs, DIMM sockets, CMOS battery, and various headers on the server board.

Connector Identification

Detailed list of board connectors including PCI slots, SATA ports, fan headers, and USB/network ports.

Hard Disk Drive Numbering

Explains the numbering and connection order for 3.5" and 2.5" hot-swap HDDs on backplanes.

MAXDATA PLATINUM 500 I Specifications

General

Brand	MAXDATA
Model	PLATINUM 500 I
Category	Server
Language	English