Maximum Controls MAX SUPER ARM 2300

Other manuals for Maximum Controls MAX SUPER ARM 2300

Manual14 pages

Questions and Answers

J
Jacob ReyesAug 12, 2025
How to troubleshoot slow movement and beeping issues with my Maximum Controls Controller gate?
- S
  Sierra ParkerAug 12, 2025
  If the Maximum Controls Controller gate moves slowly, beeps, doesn't open or close, stops prematurely, or doesn't learn limits, start by checking the GATE SPEED rotary dial to ensure it is set to the MAX position with the LED on. Also, verify the gate isn't too heavy for the operator by checking the manual for the maximum gate weight for your model. Examine the gate hinges to confirm they are not too tight. Check if the GATE “PULL open / PUSH open” switch is set properly. Ensure the manual release on the arm is locked. Relearn limit positions by clearing limits first, press STOP + CLOSE button together for 5 sec (until BEEP is heard), adjust limits and relearn NEW limits.
J
John SloanAug 16, 2025
What to do if the “MAX SENSE” LED is ON on my Maximum Controls Controller?
- J
  jfosterAug 16, 2025
  If the “MAX SENSE” LED is ON on your Maximum Controls Controller, this indicates the ERD entrapment detection is at its most sensitive setting. To resolve this, select a less sensitive setting, ideally between level 10 and 16.
S
Shirley GregoryAug 20, 2025
Why is the “ERD” LED flashing on my Maximum Controls Controller?
- S
  Susan MorganAug 20, 2025
  If the “ERD” LED is flashing on your Maximum Controls Controller, it could mean that an ERD event has occurred. Check for any obstructions blocking the gate. If there are no obstructions, the ERD sensitivity might be too high for your specific setup, so try readjusting the ERD setting.
H
Hailey HigginsAug 23, 2025
What does it mean when the “PROGRAM” LED is flashing on my Maximum Controls Controller?
- D
  Dorothy ShawAug 25, 2025
  If the “PROGRAM” LED is flashing on the Maximum Controls Controller, it means the programming mode is active. Press the button again to exit the programming mode.
M
Mr. Bryan StarkAug 27, 2025
What does it mean if the “OPEN ONLY” LED is ON or FLASHING on my Maximum Controls Controller?
- E
  Emma BrownAug 27, 2025
  If the “OPEN ONLY” LED is ON or FLASHING on your Maximum Controls Controller, it indicates that the sensor on the OPEN ONLY input (photocell or edge) may have detected an obstruction while the gate was cycling. It could also mean the photocell on the OPEN ONLY input is misaligned with the reflector, or that the sensor on the OPEN ONLY input isn't wired correctly. The sensor might not be a N.C. monitored sensor that is UL 325 2018 compliant, or the sensor is damaged or malfunctioning.
M
Michael BellAug 31, 2025
Why is the “PHOTO CLS” or “CLS ONLY 10k” LED ON or flashing on my Maximum Controls Controller?
- L
  Lisa PhillipsAug 31, 2025
  If the “PHOTO CLS” LED is ON or flashing, or the “CLS ONLY 10k” LED is ON or flashing on your Maximum Controls Controller, it might be because a sensor on the PHOTO CLS or CLS ONLY 10k inputs (like a photocell or edge) has detected an obstruction while the gate was closing. It could also mean the photocell is misaligned with the reflector, the sensor isn't wired correctly, or the sensor is not a N.C. monitored sensor that is UL 325 2018 compliant. The sensor might also need to be relearned, or it could be damaged or malfunctioning.
A
Alexandra WrightSep 4, 2025
Why is the “UL Entrap” LED illuminated on my Maximum Controls Controller?
- M
  Mariah LeonardSep 4, 2025
  If the “UL Entrap” LED is ON on your Maximum Controls Controller, it indicates that an entrapment event has occurred. Check if any entrapment sensors were triggered, and look for the PHOTO CLS, OPEN ONLY, or OPEN/CLS LEDs to be on.
T
Theresa MartinezSep 8, 2025
Why is the “OBD PORT” LED flashing on my Maximum Controls Controller?
- H
  Heather WilliamsSep 8, 2025
  If the “OBD PORT” LED is FLASHING on your Maximum Controls Controller, up to 8000 event history and error codes are being downloaded to connected flash drive. It can take up to 5 minutes.