Need help?Do you have a question about the Maytag Bravos MED6300TQ and is the answer not in the manual?
General| Brand | Maytag |
|---|---|
| Model | MED6300TQ |
| Appliance Category | Dryer |
| Capacity | 7.0 cu. ft. |
| Color | White |
| Drying Cycles | 11 |
| Energy Star Certified | No |
| Control Type | Electronic |
| Temperature Settings | Multiple |
| Wrinkle Control Option | Yes |
| Moisture Sensor | Yes |
| Power Source | Electric |
| Voltage | 240 V |
| Amperage | 30 A |
| Type | Electric |
| Width | 27 in. |
| Dryer Venting | Vented |
| Weight | 120 lb |
Explains the meaning of the safety alert symbol and associated warning words.
Explains the coding system for dryer model numbers.
Details the components and meaning of the dryer's serial number.
Lists required tools and parts for electric and gas dryer installations.
Specifies necessary clearances and site requirements for dryer installation.
Details electrical supply and connection requirements for US electric dryers.
Provides essential guidelines for safely grounding the dryer.
Critical safety and performance requirements for dryer exhaust venting.
Guidance on planning the dryer vent system for optimal performance.
Step-by-step instructions for installing the dryer's exhaust vent.
Procedures for properly leveling the dryer unit.
Instructions for connecting the gas supply to gas dryer models.
How to check and adjust the dryer's levelness.
Basic steps to start the dryer and select a drying cycle.
Details on using Sensor Dry cycles for automatic drying based on moisture.
Information on using Timed Cycles with specific time and temperature settings.
Use Air Fluff for drying items without heat, like rubber or plastic.
How to customize dryer cycles using options like Wrinkle Prevent and Damp Dry Chime.
How to enable an audible signal to indicate cycle completion.
Instructions for cleaning the dryer's lint screen before each load.
How to clean the inside of the dryer drum.
Procedures for dryer care during periods of non-use or when moving.
Instructions on how to replace the dryer's internal drum light bulb.
Steps to diagnose and resolve issues when the dryer does not start.
Troubleshooting steps for when the dryer is not heating.
Explanation of fault codes displayed on the dryer and recommended actions.
Diagnosing issues related to poor drying performance or long cycle times.
Reasons for wrinkled loads and how to prevent or fix them.
Diagrams showing the location of key internal components in electric and gas dryers.
Step-by-step instructions for removing control board components.
Procedures for removing the front cabinet panel and door switch.
Detailed steps for removing the dryer belt, drum, and rollers.
Instructions for removing the drive motor and belt switch.
Steps to remove the thermal fuse and exhaust thermistor.
Procedures for removing the flame sensor and gas burner assembly.
Steps to remove the moisture sensor and MOVs.
How to test the continuity and function of the dryer's door switch.
How to test the thermal fuse and exhaust thermistor resistance.
How to test the continuity of the dryer's flame sensor.
How to test the resistance of the burner ignitor.
How to test the resistance of the electric heater elements.
How to check the resistance of the inlet thermistor at various temperatures.
How to test the resistance of the drive motor's main and start windings.
How to test the belt switch for continuity.
Table of fault codes for electric dryers with explanations and procedures.
Steps to enter the dryer's diagnostic test mode.
How to perform the diagnostic test for the door switch.
How to perform the diagnostic test for the moisture sensor.
Displays and interprets inlet airflow values measured by the machine control.
Test to verify power supply connections to the dryer.
Test to check if power is present at the machine control electronics.
Test to check the drive motor and its circuit wiring.
Tests for the heater circuit when issues like no heat occur.
Tests for exhaust thermistor resistance and temperature readings.
How to check the inlet thermistor resistance.
Test to check continuity across the thermal fuse.
Test for moisture sensor function and short circuits.
Tests for buttons and indicator lights not functioning correctly.
Diagnostic test for the door switch functionality.
Table of fault codes for gas dryers with explanations and procedures.
Test to verify power supply connections for gas dryers.
Tests for the heater circuit in gas dryers.
Schematic diagram illustrating the electrical connections for electric dryers.
Detailed strip circuit diagrams for electric dryer components.
Schematic diagram illustrating the electrical connections for gas dryers.
Detailed strip circuit diagrams for gas dryer components.
To Next Page
