Maytag Bravos MVWB850Y

Questions and Answers

E
Eric RogersAug 17, 2025
How to fix vibration or off-balance in Maytag Washer?
- O
  oreedAug 18, 2025
  To fix vibration or off-balance issues with your Maytag Washer, ensure that both the front and rear feet are firmly in contact with the floor, and that the washer is level. The jam nuts should be tightened against the bottom of the cabinet. Also, check the floor for flexing or sagging. If the flooring is uneven, placing a 3/4" (19 mm) piece of plywood under the washer can help reduce sound.
B
bkaiserAug 20, 2025
Why is my Maytag Bravos MVWB850Y Washer not running or filling?
- C
  Christopher SalasAug 20, 2025
  If your Maytag Washer isn't running, filling, or stops working, make sure both the hot and cold water faucets are fully turned on to ensure water is flowing to the inlet valve. Also, you should check that both hoses are attached to the appliance. Check the inlet hoses for any kinks that might be restricting the water flow.
S
Stephen VasquezAug 23, 2025
Why is my Maytag Washer vibrating during spinning?
- J
  Joseph MartinezAug 23, 2025
  If your Maytag Washer vibrates during spinning or stops with a uL error code, it could be due to an unbalanced load. Make sure to load garments in loose heaps evenly around the washplate, avoiding placing items directly over the center. Adding wet items or extra water to the basket can also cause imbalance. Check the suitability of the items or load for the selected cycle. Empty pockets before washing to prevent items from falling between the basket and tub or blocking the pump.
L
Lawrence RodriguezAug 25, 2025
Why are there excessive suds in my Maytag Bravos MVWB850Y?
- L
  Lauren MckenzieAug 26, 2025
  If you notice excessive suds in your Maytag Washer, allow the washer to continue its cycle. Make sure you are only using HE (High Efficiency) detergent. Always measure the detergent and adjust the quantity based on the load size, following the detergent manufacturer’s instructions.
J
josephburtonAug 27, 2025
How to prevent load tangling in Maytag Bravos MVWB850Y?
- L
  Lori CollinsAug 27, 2025
  If your laundry load is tangling in your Maytag Washer, it could be because the wash action and/or spin speed is too fast for the load. Select a cycle with a slower wash action and slower spin speed. Keep in mind that items will be wetter than when using a higher speed spin.
S
Sarah CharlesAug 30, 2025
What does 'oL' mean on my Maytag Bravos MVWB850Y Washer display?
- O
  olsongordonAug 30, 2025
  If the 'oL' (overloaded) message appears on your Maytag Washer display, it means the load is too large. The washer will drain any water and detergent. Remove several items, add HE detergent, close the lid, and press START/PAUSE.
D
Donna SanfordSep 1, 2025
What does 'uL' mean on my Maytag Bravos MVWB850Y Washer display?
- B
  brownmarkSep 2, 2025
  If the 'uL' (unbalanced load) message appears on the display of your Maytag Washer, allow the washer to continue. If the dial is flashing and the washer has stopped, redistribute the load, close the lid, and press START/PAUSE.
K
Kelly Gilbert DVMSep 4, 2025
What does 'HC' mean on my Maytag Bravos MVWB850Y Washer display?
- D
  deborahparksSep 4, 2025
  The 'HC' code on your Maytag Washer display indicates that the cold water hose is connected to the hot water inlet and the hot water hose is connected to the cold water inlet. This code appears at the end of the wash cycle.
E
Elizabeth PorterSep 6, 2025
What does 'dL' mean on my Maytag Washer display?
- Z
  Zachary NelsonSep 7, 2025
  If the 'dL' (Lid cannot lock) message appears on your Maytag Washer display, check for items directly under the lid that may be preventing it from locking.
C
callenSep 9, 2025
What does 'lid' mean on my Maytag Washer display?
- L
  lewisaaronSep 9, 2025
  If the 'lid' (Lid opened) message appears on the display of your Maytag Washer, close the lid to clear the display. If the lid is left open for more than 10 minutes, the cycle will reset and water in the washer will drain.