Maytag MDB4949SDZ0 User Manual

Raises main wash temperature to improve cleaning for loads
containing tough, baked-on food.
PowerBlast
®
Auto
Normal
Raises main wash
temperature from
105°F to 129°F
(41°C to 54°C).
:04 to 1:16 0 to1.2
(0 to 4.5)
Sanitizes dishes and glassware in accordance with NSF
International NSF/ANSI Standard 184 for Residential
Dishwashers. Certified residential dishwashers are not
intended for licensed food establishments. Only sanitizing
cycles have been designed to meet the requirements of the
NSF/ANSI 184 performance standard for soil removal and
sanitization efficacy. There is no intention, either directly
or indirectly, that all cycles on a NSF/ANSI 184 certified
dishwasher meet the NSF/ANSI 184 performance
standard for soil removal and sanitization efficacy.
At end of the cycle, the sanitized indicator light (or “Sanitized”
on some models) will glow. If your load did not properly
sanitize, the indicator light will flash at the end of the cycle. This
can happen if cycle is interrupted or if the water does not reach
the required temperature. The light goes off when you open
and close the door or press CANCEL.
PowerBlast
®
Auto
Normal
Increases main
wash temperature
from 105°F to
145°F (41°C to
63°C) and final
rinse from 140°F
to 156°F (60°C
to 69°C).
:04 to 1:15 0 to 3.0
(0 to 11.2)
Dries dishes with heat. Use option with rinse aid to provide best
drying results. Plastic items are less likely to deform when
loaded in top rack. Turn option off for an air dry.
PowerBlast
®
Auto
Normal
Quick
Uses heating
element to speed
drying times.
:29 to :46 0
OPTIONS CAN BE
SELECTED
WITH
WHAT IT DOES ADDED
TIME TO
CYCLE
ADDED
WATER
GALLONS
(LITERS)
CONTROL PURPOSE COMMENTS
Press to start
or resume a
wash cycle.
If the door is opened during a cycle or power is interrupted, Start/Resume indicator light flashes. Cycle will
not resume until door is closed and Start/Resume is pressed.
NOTE: For top control models, push door firmly closed within 4 seconds of pressing Start/Resume. If door
is not closed within 4 seconds, the Start/Resume button LED will flash, an audible tone will be heard, and
cycle will not start.
Press to cancel
a wash cycle.
Close door firmly. The dishwasher starts a 3-minute drain (if needed). Let dishwasher
drain completely.
Control Lock
avoids
unintended use
of dishwasher
between cycles
or cycle and
option changes
during a cycle.
To turn on Lock, press and hold SANITIZE for 3 seconds. Control Lock LED will stay on, indicating that it is
activated and all buttons are disabled. If you press any button while your dishwasher is locked, LED flashes
3 times. Dishwasher door can still be opened/closed while controls are locked.
To turn off Lock, press and hold SANITIZE for 3 seconds. LED turns off.
To follow
the progress
of your
dishwasher
cycle.
Progress will be displayed by a fully lit display (and by an indicator light on the front panel of some models).
The fully lit display will glow for wash (A), dry (B), lock (C), sanitized, or clean. It will also show the
estimated remaining time for the cycle.
Front panel indicator light On some
models
The indicator light on the front of the door panel will glow green when a cycle is running and turns off when
the cycle is complete.
B
A
C

Maytag MDB4949SDZ0 Specifications

General

Style	built-in dishwashers
Color	stainless steel
Load Capacity	14
Cycle Selections	powerblast, auto, normal, quick, rinse
Options/Settings	heated dry, hi temp wash, sani rinse®, control lock, 1-24 hour delay
Delay Start	yes
Load Sensor	yes
Number of Racks	2
Water Softener	no
Food Disposer	yes
Sanitize Settings	yes
Annual Energy Consumption	270 kilowatt hours
Voltage	120 volts
Current	15 amperes

Weight and Dimensions

Depth	24.5 inches
Height	34.5 inches
Width	23.87 inches
Net Weight	89.1 pounds