-- 5 --
D Hand carry the unit with the engine stopped
and the muffler and cutting blade away from
your body.
D Allow engine to cool, empty the fuel tank, and
secure the unitbefore storingor transporting it
in a vehicle.
D Do not store the unit or fuel in a closed area
where fuel vapors can reach sparks or an
open flame from hot water heaters, electric
motors or switches, furnaces, etc.
D Store the unit so the cutting blade cannot ac-
cidentally cause injury.
D Store in a dry area out of reach of children.
D Secure the machine during transport.
GENERAL WORKING INSTRUCTIONS
This section describes the basic safety pre-
cautions forworkingwiththe hedgetrimmer. If
you encounter a situation where you are un-
certainhowto proceed, you should ask anex-
pert. Contact your authorised service dealer.
Avoid all usage which you consider to be be-
yond your capability.
WARNING: Never use a machine
without the possibility of calling for help in the
event of an accident.
BASIC SAFETY PRECAUTIONS
D Observe your surroundings to ensure that
people, animals or other things cannot affect
your control of themachine and to ensure that
the above mentioned do not come into con-
tact with the cutting equipment or objects that
can be thrown by the cutting equipment.
D Avoid usage in unfavorable weather condi-
tions. For example, thick fog, heavy rain,
strong winds or extreme cold, etc. To work in
bad weather conditions is tiring and can
create dangerous circumstances, e.g. slip-
pery surfaces.
D Make sure you can walk and stand safely.
Look out for any obstacles with unexpected
movement (roots, stones, branches, pits,
ditches, etc.) Take great care when working
on sloping ground.
D The engine should be switched off before
moving. When moving over longer distances
and transporting, the transporting guard
should be used.
D Never put the machine down with the engine
running unless you have good sight of it.
BASIC WORKING TECHNIQUES
As you become familiar with yourunit, youwill
be able to determine your own operating
pace. Conditions such as the typeand size of
material being cut will regulate the speed and
time required for your job.
D Always use two hands to operate the unit.
D Allow the cutting blades to reach full speed
before entering the material to be cut.
D Always work going away from people and
solid objects such as walls, large stones,
trees, automobiles, etc.
D If the blade stalls, immediately stop the en-
gine. Make sure the ignition switch is off, the
spark plug is disconnected, andthe blade has
stopped moving before clearing jammed de-
bris from the cutting blade. Inspect the blade
for damage and have it repaired or replaced
as needed.
D Always keep the air vents clean. Stop the
unit, make sure the cutting blade has com-
pletely stopped moving, and disconnect the
spark plug before cleaning.
SPECIAL NOTICE: Exposure to vibrations
through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damage in the fingers, hands, and joints of peo-
ple prone to circulation disorders or abnormal
swelling. Prolonged use in cold weather has
been linked to blood vessel damage in other-
wisehealthy people. If symptoms occur suchas
numbness,pain, loss of strength,change inskin
color or texture, or loss of feeling in the fingers,
hands, or joints, discontinue the use of this tool
and seek medical attention. An antivibration
system does not guarantee the avoidance of
theseproblems.Users who operate powertools
on a continual and regular basis must monitor
closely their physical condition and the condition
of this tool.
ASSEMBLY
NOTE: It is normalfor the fuel filter to rattle in
the empty fuel tank.
ASSEMBLY
No assembly is required.
OPERATION
BEFORE STARTING ENGINE
WARNING: Be sure to read the fuel
information in the safety rules before you be-
gin. If you do not understand the safety rules,
do not attempt to fuel your unit.
FUELING ENGINE
WARNING: Remove fuel cap slowly
when refueling.
This engine is certified to operate on un-
leaded petrol. Before operation, petrol must
be mixed with a good quality 2--cycle air--
cooled engine oil designed to be mixed at a
ratioof 40:1. A 40:1ratio is obtained by mixing
5 liters ofunleaded petrolwith 0,125liter of oil.
DO NOT USE automotive oil or marine oil.
These oils will cause engine damage. When
mixing fuel, follow instructions printed on oil
container. Once oil is added to petrol, shake
container momentarily to assure that the fuel
is thoroughly mixed. Always read and follow
the safety rules relating to fuel before fueling
your unit.
To Next Page
Loading...
