Medifa 800200 User Manual

medifa 8000
medifa imaging operating table
800200
Deutsch
Index
I. Safety Instructions ...................................
II. Normal Use .............................................
III. Removing the Table Top ........................
IV. Removing the Crusting Protector ............
V. Removing the Column Cover ....................
VI. Loosening of the Expansion Bellows ......
VII. Oil Level Check .......................................
- Refill Oil ...........................................
VIII. Replacement of Hydraulic Cylinder
Blocks
- Longitudinal Shifting of table top.....
- Transverse Shifting of table top ......
IX. Mounting of the Upper Base ...................
X. Replacement of the Way measurement
System for ...........................................
- Longitudinal Shifting .......................
- Transverse Shifting .........................
- Trendelenburg Shifting ...................
- Lateral Tilt
XI. Replacement of Hydraulic Cylinder ...............
-Trendelenburg Shifting ...........................
-Lateral Shifting .......................................
XII. Replacement of the Control Panel .................
XIII. Replacement of the Hydraulic Power Unit .....
XIV. Replacement of Accumulator .........................
XV. Replacement of Movable Parts .....................
- Replacement of the Castors(front) ...........
- Replacement of the Castors (rear) ............
XVI. Replacement of the External Battery Charger ..
XVII. Wiring Diagram Breaker Box (black) .................
XVIII. Electrical Wiring diagram ...............................
XIX. Hydraulic Diagram .........................................
XX. List of Spare Parts & Drawings ......................
XXI. Service/Maintenance Schedule .....................
- Service Report .......................................
- Maintenance Schedule ..........................
23-25
23
24-25
26
27
28
29-32
29
30-32
33
34
35
36-37
38-39
40-44
40-41
42-44
2
3
4
5
6-9
10
11
11
12-15
12-13
14-15
16
17-22
17
18
19-20
21-22

Medifa 800200 Specifications

General

Category	Medical Equipment
Model	800200
Manufacturer	Medifa
Type	Operating Table
Application	Surgical procedures
Power Supply	220-240 V, 50/60 Hz

Summary

I. Safety Instructions

DANGER OF TILTING!

Warning about potential tilting hazards during adjustments.

General Safety Precautions

General safety rules and recommendations for operating the table.

II. Normal Use

Operator Training Requirement

Manual content is based on skilled staff training; it doesn't replace essential training.

III. Removing The Table Top

Securing Table Top During Removal

A second person should secure the table top before removing the last screws.

IV. Removing The Crusting Protective Cover

Securing Cover Panel During Removal

A second person should secure the cover panel before removing the last screw.

V. Removing The Column Cover

Preventing Cover Fall Hazard

Be careful to prevent the cover from falling down during removal.

VII. Oil Level Check

Collision Avoidance During Oil Check

Avoid collisions between table plate and floor during end position functions.

VIII. Hydraulic Cylinder Replacement (Longitudinal)

Pressurized Oil Hazard

Oil might penetrate if cylinders/tubes are pressurized; use a collecting pan.

VIII. Hydraulic Cylinder Replacement (Transverse)

Securing Base Plate During Removal

IX. Mounting Upper Base Plate

Base Plate Rail Protection

Do not pull base plate completely out of guide rails to avoid destruction.

X. Replacing Way Measurement System (Longitudinal)

X. Replacing Way Measurement System (Transverse)

X. Replacing Way Measurement System (Trendelenburg)

X. Replacing Way Measurement System (Lateral)

Driving Pin Position Marking

XI. Hydraulic Cylinder Replacement (Trendelenburg)

Upper Structure Securing During Removal

Cylinder Securing During Bolt Removal

XI. Hydraulic Cylinder Replacement (Lateral)

Upper Structure Fixation Caution

XII. Control Panel Replacement

XIII. Hydraulic Power Unit Replacement

Power Unit Securing During Removal

XII. Accumulator Replacement

Exposed Contact Short Circuit Hazard

Reconnect Cables After Replacement

XIV. External Battery Charger Replacement

XV. Wiring Diagram Breaker Box

XVI. Electrical Wiring Diagram

XVII. Hydraulic Diagram

XIX. Service and Maintenance Schedule

XIX. Service Report and Maintenance Schedule

IEC 601 Safety Checks

Safety checks according to IEC 601 standards, including discharged current.