(2) PILOT LAMP -- This light will comes on when the power supply is on.
(3) EMERGENCY STOP -- This switch is used for emergency case to stop the machine only.
Turn this switch clockwise makes power source on. When this switch is pressed, all machine's operation
stop immediately.
(4) POWER SWITCH ON -- This switch is used for turning on the power by depressing it.
(5) POWER SWITCH OFF -- This switch is used for turning off the power by depressing it.
(6) HYDRAULIC "ON" LAMP -- When NO.(4) button is depressed, the hydraulic pump motor operates.
This lamp is light.
(7) BLADE DRIVE BUTTON -- When this button is pressed, both the saw blade motor and the cutting
fluid pump operate and saw head begins to descend. The saw head descends quickly until the feeler of
the quick approach device comes into contact with the workpiece and thereafter, it will descend at the
designated cutting speed.
(8) FRONT VISE SWITCH -- The switch control the front vise jaws in manual mode, The front vise
clamp when turn the switch to right. Then if release the switch, the switch come back to the middle
position, the vise doesn’t hold the workpiece. If operator would like to hold the workpiece, he would
follow the (9) illustration.
The front vise open little by little if the guide arm is under the front vise when the switch turn to left.
And the front vise open continuously if the guide arm is above the front vise. At last, if release the
switch, the switch come back to the middle position.
(9) FRONT VISE TO CONFIRM SWITCH – The front vise clamp the workpiece when turn switch
NO.(8) right and press button NO.(9) 1.5sec in the same time. Then the front vise hold the workpiece
after the lamp NO.(9A) light.
(10) REAR VISE SWITCH -- This switch control the rear vise jaws in manual mode, switched to the left
makes the front vise open. and switched to the right makes the front vise clamp.
(11) AUTO - MANUAL SELECTOR -- For continuous cutting , turn this selector to left "AUTO".
To individually operate each function, turn this switch to right "manual".
(12) MANUAL FEED FORWARD --When this button is pressed the workpiece moves forward.
The workpiece stops advancing when the button is released.
NOTE: Turn (8) VISE SWITCH right position before depress switch (7) BLADE DRIVE to cutting.
(13) MANUAL FEED BACKWARD --When this button is pressed the workpiece moves backward.
The workpiece stops moving when the button is released.
NOTE: Don't depress (12) and (13) two switches, if the workpiece are clamped by both front and
rear vises in the meantime.
(14) QUICK APPROACH BUTTON -- While this button is pressed, the saw head descends quickly.
This button is used to cause the saw blade to approach the work quickly when the saw blade is at a
distance from the workpiece. When the feeler of the quick approach device comes into contact with
the work, the saw head stops descending at that position even this button is still pressed.
(15) SAW FRAME RAISE BUTTON -- When this button is pressed, the saw blade motor stops and the
saw head ascends. The saw head stops ascending at that position when the button is released.
(16) WORK BEAM LIGHT SWITCH -- When this switch is set at "1" the work light illuminates.
(17) COOLANT SWITCH -- When this switch is set at "1" the cutting fluid pump operates and cutting
fluid will be injected even though the saw blade motor is not in operation.
Use this switch when removing saw chips with the cutting fluid (without the blade running).
(18) INVERTER CONTROL KNOB (OPTIONAL)-- Please turn left for being slow speed wanted,
turn right for being fast speed wanted. Please refer to (JPS) Inverter Instruction Manual or Please
refer to (TOSHIBA) Inverter Instruction Manual
(19) FEED RATE CONTROL KNOB -- When this control dial is turned clockwise the feed rate of
the cutting increases, when it is turned counter clockwise, the feed rate decreases.
4 - 2
To Next Page
Loading...