11
7.2 Cleaning the grinder
Note: You can call up cleaning and care
instructions by using the QR code.
Clean the grinder if you see visible soiling.
After each time you clean the grinder, you
should also clean the ground coffee chute.
•Emptythebeancontainer.Allowthegrinderto
grind itself empty. Do this by fitting a filter in the
filter insert and starting the grinding process
withthe“Start/Stop”button.
•Turnthegrindingnenessregulatoruntilthetwo
triangles point towards each other . Pull the
grinding fineness regulator vertically upwards out of
the appliance .
•Cleanallpartsofthegrinderwiththebrush.
•Cleanthelowergrindingdisc, the gap
and the
entrance to the ground coee chute
s
. You can
remove loose ground coee with a vacuum cleaner.
Loosen caked-on ground coee with the brush.
•Pullthesiliconeringothedisccarrier.
•Youcanremovethegroundcoeefromthegrinding
ring by tapping it lightly. You can also remove the
ground coee with a vacuum cleaner. If it is heavily
soiled, you can clean the grinding ring under running
water. Allow the grinding ring to dry completely.
•Reassemblethegrindingnenessregulator.Make
sure you press the silicone gasket evenly and as far
as it will go into the grinding ring.
•Tolockthegrindingring,turnittotheposition
shown .
•Insertthegrindingnenessregulatorverticallyinto
the appliance. The two triangles must point towards
each other . Turn the grinding fineness regulator
clockwise up to the stop to lock it.
Clean the ground coffee chute:
•Holdingtheapplianceinbothhandscarefullylayit
on its back.
•Nowyoucanrstlycleantheareaabovetheswivel
filter with the brush and a damp cloth.
•Toopenthegroundcoeechute
hold down the
button for ground coee o for 5 seconds.
•Thegroundcoeechuteapopensandthechute
can be cleaned with the brush..
•Toclosetheaponthegroundcoeechutehold
down the button for ground coee o for 5 seconds.
•Puttheswivellterjbackinplaceandstandthe
appliance up again.
Descaling:
Based on the water hardness you have set (see
point 3) the appliance should be descaled soon after
the CALC indicator lights up.
•Measureoutthedescalinguidaccordingtothe
manufacturers instructions and pour it into the
water tank. We recommend using Melitta
®
“Anti
Calc Liquid for Filter Coffee & Aqua Machines“.
•BrieypresstheCALCbutton. The red LED
starts to flash .
•Thecurrenttimeand‘CALC’appearalternatelyin
the display .
•Thedescalingprocessrunsautomatically.Toremove
even heavy calcification the descaling process takes
about 25 minutes.
•Attention: Only by running the complete descaling
process can all limescale deposits be removed. Only
then does the Calc LED go o. Therefore the
descaling process should not be interrupted.
•Afterthedescalingprocesshasbeencompletedthe
light in the CALC button goes o. The appliance
turns o automatically.
•Tocompletelyremoveanydepositsfromdesca-
ling, the appliance must be rinsed twice with the
maximum amount of water without coee, after the
descaling process has ended. Proceed as described
in point 2.
8. Note on disposal
•Applianceslabelledwiththissymbol are subject
to European guidelines for WEEE (Waste Electrical
and Electronic Equipment).
•Electricappliancesdonotgointhehouseholdbin.
Dispose of the appliance in an environmentally
friendly way using suitable collection systems.
•Packagingmaterialsarerawmaterialsandcanbe
recycled. Please recycle them.