Menards Master-force MFX3I2700

Questions and Answers

A
Ashley Johnson MDAug 7, 2025
What to do if Menards Master-force MFX3I2700 Pressure Washer turns on for 2 seconds, shuts off, and won't turn back on?
- J
  James McbrideAug 7, 2025
  When the water is connected, the accessories are assembled properly, and the power is turned on, the Menards pressure washer may turn on for 1 - 2 seconds to prime the pump. It automatically shuts off and waits for the spray gun trigger to be pressed. When the trigger is pressed, water starts flowing through the pump. The water sensor in the pump “senses” the moving water and automatically turns the pressure washer on. You can also try turning the power off, holding in the trigger on the spray gun so that you have a steady stream of water. While you are holding the trigger open on the spray gun, at the same time, turn the power on.
J
Jonathan HansenAug 14, 2025
How to fix a Menards Master-force MFX3I2700 that will not turn on?
- N
  Nicole CooperAug 14, 2025
  If your Menards pressure washer unit won't turn on, ensure the pressure washer is OFF. Plug the electrical cord into a grounded 120 volt outlet, avoiding extension cords. If the cord doesn't fit, the outlet may not be properly grounded; use a different outlet. If the issue persists, try another outlet. If it still doesn't work, contact Customer Service at 1-866-235-5112.
C
Chase NelsonAug 21, 2025
Why is water leaking where the high pressure hose connects to the spray gun on my Menards Pressure Washer?
- O
  Olivia SmithAug 21, 2025
  If water is leaking where the high pressure hose connects to the spray gun of your Menards Pressure Washer, make sure there is an o-ring at the end of the metal tip of the high pressure hose. If no o-ring is present, the connection between the hose and spray gun will leak. An O-Ring Replacement Kit (D) is included with purchase. Additional O-Ring Kits are available online at www. arblueclean.com or by calling Customer Service at 1-866-235-5112 to place an order.
N
Nicole CraigAug 30, 2025
What to do if my Menards Pressure Washer is running but there is no water flow?
- A
  Amber JohnsonAug 30, 2025
  If there is no water flow when the unit is running on your Menards pressure washer, remember that power should NOT be turned on until water comes through the spray gun, as doing so will damage the motor. You should also check the water source, eject the nozzle from the lance to determine if clog is coming from the nozzle (If nozzle is clogged, see nozzle cleaning instructions under “Cleaning nozzles”), take off the lance and just spray out of the spray gun to indicate if the problem is with the lance, and check the Garden Hose Adapter for loose connection and the filter for debris.

Summary

Product Specifications

Package Contents

Hardware Contents

Safety Information

Ground Fault Circuit Interrupter Protection

Explains GFCI protection built into the power cord for electric shock prevention.

Preparation

Assembly Instructions

Frame Assembly

Instructions for assembling the main frame and wheels of the pressure washer.

Extension Lance Installation

Steps for attaching the extension lance to the spray gun securely.

Foam Cannon Installation

Guide on how to install and prepare the foam cannon for use.

Foam Cannon Storage

Instructions on where to store the foam cannon on the pressure washer unit.

Operating Instructions

Adjusting Soap Levels on Foam Cannon

How to adjust the soap concentration using the foam cannon's control knob.

Operation Tips

Important operational tips, including GFCI testing and priming the pump.

Using Power Cord

Instructions on how to detach the power cord for use and for storage.

Care and Maintenance

Detergents

Guidance on selecting and using appropriate detergents for pressure washing.

Cleaning Garden Hose Adapter

Instructions on how to clean the screen inside the garden hose adapter.

Cleaning Nozzles

Procedure for cleaning clogged or partially clogged nozzles.

Storage

Detailed instructions on how to properly store the pressure washer.

Pump Saver

Pump Saver Instructions

Step-by-step guide on how to use the pump saver product for protection.

Troubleshooting

Replacement Parts List

Limited Warranty

Warranty Process

Steps to follow for initiating a warranty claim or returning the unit for repair.