EasyManua.ls Logo

metso automation neles NP726

Default Icon
20 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
POSITIONERS
Series NP
Installation, Maintenance and
Operating Instructions
7 NP 72 en
Issue 5/02
Question and Answer IconNeed help?

Do you have a question about the metso automation neles NP726 and is the answer not in the manual?

metso automation neles NP726 Specifications

General IconGeneral
Output SignalPneumatic
Supply Pressure1.4 - 7 bar (20 - 100 psi)
Temperature Range-40°C to +85°C (-40°F to +185°F)
Enclosure RatingNEMA 4X, IP66
Housing MaterialAluminum

Summary

1 INTRODUCTION

1.1 General

Basic information on the positioner.

1.2 Operating principle

Explains the force balance principle of operation.

1.3 Marking of positioner

Describes the ID plate and its information.

1.4 Technical specifications

Lists key technical parameters like signal ranges and pressures.

1.5 Approvals

Lists certifications like CENELEC, CSA, FM.

1.6 Recycling and disposal of a rejected positioner

Guidelines for recycling and disposal.

1.7 Safety precautions

Important safety warnings and cautions.

2 MOUNTING ON THE METSO AUTOMATION ACTUATOR

2.1 General

General notes on mounting positioners with actuators.

2.3 Installing positioner NP700 S2 on Metso Automation Series B actuators

Steps for mounting S2 positioner on Series B actuators.

2.4 NP700700 positionerlimit switch combination

Instructions for combining positioner with limit switch.

2.5 Piping of supply and signal air

Guidance on connecting air supply and signal lines.

3 INPUT SIGNAL AND DIRECTIONS OF OPERATION

3.1 Changeover piece

Explains the function and setting of the changeover piece.

3.2 Cam plate

Describes the cam plate markings and signal ranges.

4 PRELIMINARY ACTIONS FOR THE ADJUSTMENT

4.1 Position of the changeover piece

Steps for setting the changeover piece position.

4.2 Pilot valve

Notes on the pilot valve, removal unnecessary for changeover.

4.3 Position of the cam plate

Steps for setting the cam plate position.

5 BASIC ADJUSTMENT

Basic Adjustment Steps

Detailed steps for performing basic adjustment.

6 0-ADJUSTMENT

0-ADJUSTMENT

Explains adjustment for ball valves considering 'dead angle'.

7 SPLIT-RANGE ADJUSTMENT

SPLIT-RANGE ADJUSTMENT

Method for split range adjustments using cam plate.

8 MAINTENANCE

8.1 Supply air filter

Maintenance of the supply air filter.

8.2 Pilot valve

Instructions for pilot valve removal and cleaning.

8.3 Replacement of the diaphragm

Steps for replacing the diaphragm.

9 TROUBLE SHOOTING

TROUBLE SHOOTING

Lists common problems and their potential causes.

10 OPTIONS

10.1 NP700 B and NP700 B1

Options for flameproof enclosure I/P converter.

10.2 NP700 GN natural gas construction

Natural gas construction details.

10.3 NP700 R dust-proof construction (IP 65)

Dust-proof construction details.

10.4 NP700 A with pressure gauges

Option for positioners with pressure gauges.

11 TOOLS

TOOLS

Equipment needed for adjustments.

12 ORDERING SPARE PARTS

ORDERING SPARE PARTS

Information required for ordering spare parts.

13 DRAWINGS AND PARTS LISTS

13.1 Exploded view and parts list

Detailed exploded view and parts list.

13.2 Mounting parts for B1 C6-502 and B1 J8-322 actuators (S1)

Lists mounting parts for specific actuators.

13.3 Mounting parts for Quadra-Powr actuators (S1)

Lists mounting parts for Quadra-Powr actuators.

13.4 Mounting parts for B1 C6-20 and B1 J8-20 actuators (S2)

Lists mounting parts for specific actuators.

13.5 Mounting parts for B1 C25-502 and B1 J25-322 actuators (S2)

Lists mounting parts for specific actuators.

14 TYPE CODE

TYPE CODE

Explains the product type code structure and options.

Related product manuals