Body
Fittings
Cubby
box
To open. Press the b
utto
n (I )
and
lower the flap.
To lock. Insert the key and t
urn
clockwise.
To unlock.
Turn
the key anti-clockwise.
Hard
top
Fitting. Lower the h
ood.
Fig. 3 and 4
Position
the
hard
top
on
the
car
and engage
the
toggle faste ner
tongu
es in their
sockets
on
the
windscreen rail.
Che
ck
that
the
rubb
er sealing strip is corre ctly
positioned for
ward
of the rail. Fasten the toggle link s and lock them with the
securing
bra
ckets (inset,
Fig
. 3).
Fit
the bolts
into
both
side-fixing
brackets
and
tighten
them
do wn gentl y and evenly.until the
hard
top
seals at
both
sides
and
the
rear.
Do
not
tighten the
bolts
ha rd
down
.
Dra in point s
The
body and doors
are
prov
ided with drain hol es to
allo
w ra in-wa ter and
Fig. 6 condensation to flow freely from the panels,
thu
s prev
enting
accumulated water
from
causing r ust and c
orros
ion. It is essential that
the
dr
ain
holes are kept
clear and
are
not inad vertently blocked.
Wh
en p
ainting
or applying
unde
rsea I
to the bo dy
und
erpan els or do
or
s, te
mporar
ily
seal
or
ma
sk the
dr
ain holes to
prevent the
ingr
ess
of
sealant. Period ically inspect the
drain
holes and clear an y
o
bstr
uction usin g a piece of stiff wire or a suitable tool.
Jacking up bene
ath
the
underfloor
may d
eform
the
drain
aperture
s; always use
the jacking
point
s
pro
vided.
Che
ck the
width
of
the
gap between.the flanges of
the
side-fixing
bracket
s (see
Fig. 4),
remove
the
bolts
and
fit
packing
washers between
the
flanges to
the
thickne
ss
of
the gap .
Refit
and
tighten the securing bolts.
Bo nnet
To
raise the
bonnet,
pull the
knob
(1) located inside
the
ca r
on
the
left-hand side
Fig. 5 below the fascia panel.
Fig. 5
Press
th
e safety
catch
(2)
und
er
the
f
ront
of
the
bonnet
and raise
the
bonn
et.
When
fully ra ised the
support
s
tay
will
autom
atically spring
into
engagement
and
the
bonn
et will be held in
the
op
en position.
To
close, raise the
bonnet
slightly, push
the
catch
(3)
on
the
bonnet
stay rea rwards
to release
the
locking mech
ani
sm
and
lower
the
bonn
et.
Appl
y light pres
sure
with
the
palms
of
the
hand
s at
the
front
corners
of
the
bonnet
and press do wn
quickly ;
und
ue force is
not
necessary
and
ma
y
cause
damage.
The
safety
catch
and
lock
will be
heard
to engage.
n
Jac
king up bene
ath
the
underfloor
may d
eform
the
drain
aperture
s; always use
the jacking
point
s provided.
Fig
. 6
Fig.4
.
\,
-=
Fig. 3 and 4
Position
the
hard
top
on
the
car
and engage
the
toggle fastener
tongu
es in their
so
ckets
on
the
windscreen rail.
Check
that
the rub
ber
sealing str ip is
cor
rectly
positioned
for
ward
of the rail. Fasten the toggle link s
and
lock them with th e
securing
bra
ckets (inset,
Fig
. 3).
Fit
the bolts
into
both
side-fixing
brackets
and
tighten
them
do wn gentl y and evenly .until the
hard
top
seals at
both
sides
and
the
rear.
Do
not
tighten the
bolts
hard
down
.
Fig. 3
Che
ck the
width
of
the
gap between.the flanges of
the
side-fixing
bracket
s (see
Fig. 4),
remove
the
bolts
and
fit
packing
washers between
the
flanges to
the
thickness
of
the gap.
Refit
and
tighten the securing bolts.
To Next Page
Loading...
Need help?
General
