7
English
DeutschFrançais
Italiano
Nederlands
Español
C. Scanning from an image-editing
application
In the example below, we use Adobe PhotoDeluxe 2.0, an
image-editing application that is included in a separate CD
in your scanner package. Refer to page 2 for software
installation details.
1. Launch Adobe PhotoDeluxe. a) For PCs: Go through
the Windows menu -- click Start, Programs, Adobe,
PhotoDeluxe, Adobe PhotoDeluxe. b) For Macs:
Launch PhotoDeluxe from its folder.
2. When PhotoDeluxe launches, click the following in
succession: the
Get Photo Get Photo
Get Photo Get Photo
Get Photo button, the
Get PhotoGet Photo
Get PhotoGet Photo
Get Photo tab,
and the
ScannersScanners
ScannersScanners
Scanners button.
3. Do either of the following: a) For PCs: Select
MicrotekMicrotek
MicrotekMicrotek
Microtek
ScanWizard 5ScanWizard 5
ScanWizard 5ScanWizard 5
ScanWizard 5 as your “Source”, and click OK. b) For
Macs: Select
ScanWScanW
ScanWScanW
ScanW
izarizar
izarizar
izar
d 5 Td 5 T
d 5 Td 5 T
d 5 T
wain wain
wain wain
wain as your “Source”,
and click OK.
Federal Communications Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, (example - use only shielded interface cables
when connecting to computer or peripheral devices). Any changes or modifications not
expressly approved by the party responsible for compliance could void the user’s authority
to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Responsible Party: Loi Han
3715 Doolittle Drive
Redondo Beach, CA 90278-1226
U.S.A.
Telephone No: 1-310-297-5000
Federal Communications Commission Interference Statement
This equipment (Model: MRS-2400G12U) has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Note: 1) A shielded of USB interface cable with ferrite core installed on the scanner connector
end must be used with this equipment. 2) AC adapter with ferrite core installed on the
scanner connector end must be used with this equipment.
CAUTION
Changes or modifications not expressly approved by the manufacturer responsible for
compliance could void the user's authority to operate the equipment.
TT
TT
T
ake note :ake note :
ake note :ake note :
ake note :
If ScanWizard 5 is launched from any image-editing
application (such as PhotoDeluxe), the Copy and
E-mail
on the ScanWizard 5-Standard Control Panel
interface will be deactivated. However, using the Copy or
E-mail buttons from the scanner’s front panel will cause the
scanner to perform a fast preview.
4. Click the
Scanner Scanner
Scanner Scanner
Scanner icon from the PhotoDeluxe Panel to
launch ScanWizard 5.
5. The
ScanWizard 5-Standard Control Panel
appears.
See the procedures described in the previous section,
“Launching ScanWizard 5 as a stand-alone program”
on page 6 (#1 to #3) for more information.
6. Click
ScanScan
ScanScan
Scan, and the image will be scanned and
delivered to PhotoDeluxe. For more details on
PhotoDeluxe, consult the PhotoDeluxe on-line help.
Trade Name Model Number
ScanMaker 4700 MRS-2400G12U
Tested to Comply
With FCC Standards
FOR HOME OR OFFICE USE
To Previous Page
Loading...
Need help?
General
