MidNite Solar Classic 200 User Manual

Name: MidNite Solar Classic 200
Brand: MidNite Solar
Rating: 4 (1 reviews)

102 pages

To Next Page

1 | P a g e

MidNite Solar Classic

Owner’s Manual

Standard Classic Classic Lite

This Manual covers models Classic 150, 200, 250 &

250KS as well as the Classic 150, 200, 250 & 250KS LITE

Default Chapter3
- Table of Contents3
Glossary of Terms5
Scope7
Introduction7
Classic Power Curves9
Unpacking the Classic11
Removing and Installing the Front Cover on the Classic12
Mounting the Classic13
- Alternative Mounting15
  - Dimensions15
- Sealed or Vented16
Battery Temperature Compensation16
Classic Stacking Cable Routing and Installation Guidelines17
Battery Temperature Sensor Installation18
Chassis Grounding20
- DC System Grounding20
DC GFP (Ground Fault Protection)21
- Disabling GFP21
Wiring the Classic22
- DC Terminal Connector25
Over Current Protection and Wire Size Requirements25
- Current Rating25
- Over Current Protection26
- Long Distance Wire Runs26
- Connecting the Classic to the Clipper26
- Maximum and Minimum Wire Size27
Equalization Manual and Auto28
- Equalization with the Classic Lite28
- Equalization with the Standard Classic29
Standard Classic Programming30
- Commissioning the Classic (Quick Start)30
- Battery Charge Stages and Meanings30
  - Resting30
  - Mode Is off31
- Adjusting Absorb, Equalize and Float Voltages31
- Current Limit31
- LED Modes and the "Blinking Red LED31
- Calibrating Battery and PV Voltage32
- Configuring DC Input Source32
- Configuring the Classic for Wind Input Source34
- Setting the Date and Time35
- Setting Longitude and Latitude35
- Configuring Auxiliary Input/Output35
  - Aux 1 Function39
  - Aux 2 Function. Output/Input40
- Setting the MNGP Features41
- Navigating the Menu's41
- Viewing Other Midnite Products on the Display42
- Connecting Classic to Two Mngps/Network Cable42
- Arc Fault43
- View Faults and Warning's44
- View Logged Data44
- Graphical Logging Display Modes47
- Dealer Information Screen49
Classic Lite Programming50
- LED Explanations50
- Programming51
- Dip Switches51
- Section 1 Switch Settings Explained53
- Section 2 Switch Settings Explained54
  - Battery Voltage and Time Settings57
- Using MNGP Remote to Program a Classic Lite58
- Programming the Lite with a Networked Standard Classic58
- Programming the Lite with the Local App59
- Clearing Faults59
- Notes on the Lite59
- Explanations of Solar and Legacy59
Uploading New Firmware to the Classic60
Connecting the Classic to the Internet63
- Networking63
- Network Setup through the MNGP64
- Web Access66
- Local Network66
Positive Ground Systems66
Hypervoc67
Troubleshooting68
Specifications Electrical69
Specifications Mechanical70
Default Battery Charge Set Points71
Optional Accessories71
Regulatory Approval71
Warranty72
Appendix73
- Aux 1 and Aux 2 Graphs/Jumpers73
- Aux 1 Voltage-Time Relation (Relay/12V)74
- Aux 2 Voltage-Time Relation (PWM)74
- Classic Breaker Sizing75
- Label Set from Classic77
- Modbus78
- RS232 Jack Pin out102

Questions and Answers:

Need help?

Do you have a question about the MidNite Solar Classic 200 and is the answer not in the manual?

MidNite Solar Classic 200 Specifications

General

Model	Classic 200
Type	MPPT Charge Controller
Efficiency	98%
Temperature Range	-40°C to +60°C
Display	LCD
Maximum PV Input Voltage	200 VDC
Maximum Output Current	79A
Communication	RS-232, Ethernet
Maximum Input Voltage	200 VDC
Nominal Battery Voltage	12/24/48 V
Dimensions	12.5 x 8.5 x 4.5 in

Related product manuals

MidNite Solar Classic 250

102 pages

MidNite Solar Brat

24 pages

MidNite Solar Classic 200 User Manual

Table of Contents

Questions and Answers:

MidNite Solar Classic 200 Specifications

Related product manuals