MikroTik CCR1036-12G-4S Series User Manual

CCR1036-12G-4S-series
CCR1036-12G-4S-EM
CCR1036-12G-4S
Safety Warnings
Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing
accidents.
Ultimate disposal of this product should be handled according to all national laws and regulations.
The Installation of the equipment must comply with local and national electrical codes.
This unit is intended to be installed in the rackmount. Please read the mounting instructions carefully before beginning installation. Failure to use the
correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system.
This product is intended to be installed indoors. Keep this product away from water, fire, humidity or hot environments.
Use only the power supply and accessories approved by the manufacturer, and which can be found in the original packaging of this product.
Read the installation instructions before connecting the system to the power source.
We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your
own risk!
In the case of device failure, please disconnect it from power. The fastest way to do so is by unplugging the power plug from the power outlet.
It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling
requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik devices must be professionally installed.
Firs Use
The device comes preinstalled with RouterOS and is ready to use. The ETH1 port has a default IP address for connecting: 192.168.88.1. The username is
admin and there is no password Please connect with your web browser to this IP address and choose Webfig to configure it. In case the IP connection is .
not available, the Winbox tool ( ) can be used to connect to the MAC address of the device.https://mt.lv/winbox
The device doesn't have any other configuration or firewall rules applied by default, please connect to it, and set up IP addresses, users, passwords,
firewall, etc. Please ensure you have prevented unauthorized access from public networks by use of the firewall filters and restrictions available in the IP
services menu in RouterOS.Detailed info on how to upgrade the device ;https://mt.lv/upgrade
See this page for connection and configuration guides: +https://mt.lv/help+
Powering
The device accepts powering from two redundant power supplies, each accepts 100-240 V AC power. You can use either, or both at the same time. Up to
60 W power consumption.
Extension Slots and Ports
12x 10/100/1000 Ethernet ports.
4x SFP cage
USB 2.0 type A
One M.2 slot, type PCIe x4
RJ45 console port
Etherboot / Netinstall is available on port ETH12.
Mounting

MikroTik CCR1036-12G-4S Series Specifications

General

CPU	Tilera Tile-Gx36
CPU Cores	36
CPU Nominal Frequency	1.2 GHz
RAM	4 GB
RouterOS License	Level 6
Max Power Consumption	60 W
Architecture	TILE
Storage Type	NAND
Serial Port	RS232
Operating System	RouterOS
CPU Temperature Monitor	Yes
Voltage Monitor	Yes
PCB Temperature Monitor	Yes
AC Input Range	100-240 V
Ethernet Ports	12
SFP Ports	4
Power Supply	Dual
MTBF	200, 000 hours at 25C

Summary

Safety Warnings and Precautions

General Safety Guidelines

Adhere to national laws, electrical codes, and use caution with electrical circuitry. Ensure proper installation and environment.

First Use and Configuration

Initial setup via Webfig or Winbox using default IP 192.168.88.1. Secure device by setting up passwords and firewall rules.

Powering the Device

Device accepts power from two redundant 100-240V AC supplies, with a maximum consumption of 60W.

Hardware Ports and Slots

Details 12x 10/100/1000 Ethernet, 4x SFP cages, USB 2.0, M.2 slot, and RJ45 console port. Netinstall on ETH12.

Hardware Overview and Operation

Mounting Instructions

Device can be rackmounted or placed on a desktop. Use rack ears and Phillips screwdriver for installation.

Buttons and Jumpers Functions

Describes RouterBOOT reset button functions for default reset, configuration clear, and Netinstall server search.

LED Indicators

Explains the four LEDs: PWR1/2 for power supply status, FAULT for cooling fans, and USER for software configuration.

Operating System Support

Device supports RouterOS software. Other operating systems have not been tested.

Regulatory Compliance Statements

FCC Interference Statement

Equipment tested for Class A digital device limits. Must use shielded cables to ensure compliance and avoid interference.

Industry Canada Compliance

Complies with license-exempt RSS standards and ICES-003 for Class A digital apparatus.

UKCA Marking

Indicates compliance with UK regulatory requirements.

Eurasian Conformity Mark

Information on manufacturing date, manufacturer details, and warranty for Eurasian market.

Additional Compliance and Information

Norma Oficial Mexicana (NOM)

States compliance with energy efficiency standard NOM-029-ENER-2017, subject to two operational conditions.

CE Declaration of Conformity

Provides link to the full EU Declaration of Conformity text for the device.