EasyManuals Logo

MikroTik RB4011iGS+5HacQ2HnD-IN User Manual

MikroTik RB4011iGS+5HacQ2HnD-IN
6 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
RB4011iGS+5HacQ2HnD-IN
RB4011iGS+5HacQ2HnD-IN
The device is already configured with basic settings, you can simply plug in your ISP cable and start using the Internet. We recommend you to set up a
password to secure your device.
Safety Warnings
Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing
accidents.
Ultimate disposal of this product should be handled according to all national laws and regulations.
The Installation of the equipment must comply with local and national electrical codes.
This unit is intended to be installed in the rackmount. Please read the mounting instructions carefully before beginning installation. Failure to use the
correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system.
This product is intended to be installed indoors. Keep this product away from water, fire, humidity or hot environments.
Use only the power supply and accessories approved by the manufacturer, and which can be found in the original packaging of this product.
Read the installation instructions before connecting the system to the power source.
We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your
own risk!
In the case of device failure, please disconnect it from power. The fastest way to do so is by unplugging the power plug from the power outlet.
It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling
requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik radio devices must be professionally installed.
Exposure to Radio Frequency Radiation: This MikroTik equipment complies with the FCC, IC, and European Union radiation exposure limits set forth for an
uncontrolled environment.This MikroTik device should be installed and operated no closer than 20 centimeters from your body, occupational user, or the
general public.
Setup
Choose your powering solution, please see the section for possibilities.Powering
Connect your Internet cable to port 1, and local network devices to other ports.
Set your computer IP configuration to (DHCP).
automatic
Wireless access point mode is enabled by default.
Connect your direct input power jack if not using POE, to start up the device.
The device will boot up and after a short beep Wireless network will be available for connecting.
Open network connections on your PC, mobile phone, or other device and search for MikroTik wireless network and connect to it.
Once connected to the wireless network, open in your web browser to start configuration, since there is no password by https://192.168.88.1
default, you will be logged in automatically.
We recommend clicking the "Check for updates" button and updating your RouterOS software to the latest version to ensure the best
performance and stability.
Choose your country, to apply country regulation settings, and set up your password on the screen that loads.
Powering
The power consumption under maximum load can reach 44 W. The device accepts power from the power jack or from the first Ethernet port:
Direct-input power jack (5.5 mm outside and 2 mm inside, female, pin positive plug) accepts 12-57 V DC.
First Ethernet port accepts Power over Ethernet 18-57 V DC.

Other manuals for MikroTik RB4011iGS+5HacQ2HnD-IN

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the MikroTik RB4011iGS+5HacQ2HnD-IN and is the answer not in the manual?

MikroTik RB4011iGS+5HacQ2HnD-IN Specifications

General IconGeneral
Processor cores4
Processor modelAnnapurna Labs Alpine AL21400
Built-in processorYes
Processor frequency1400 MHz
Memory card slot(s)-
Product typeTabletop router
Product colorBlack
Wi-Fi bandDual-band (2.4 GHz / 5 GHz)
Wi-Fi standards802.11a, Wi-Fi 5 (802.11ac), 802.11ad, 802.11g, Wi-Fi 4 (802.11n)
Top Wi-Fi standardWi-Fi 5 (802.11ac)
WLAN data transfer rate (max)1733 Mbit/s
Ethernet LAN data rates10, 100, 1000 Mbit/s
Ethernet LAN interface typeGigabit Ethernet
Output current0.6 A
Output voltage57 V
Power source typeDC
Power consumption (typical)26 W
Weight and Dimensions IconWeight and Dimensions
Depth120 mm
Width228 mm
Height30 mm

Related product manuals