MikroTik RouterBOARD 2011UiAS-RM

1.
2.
3.
4.
5.
6.
7.
8.
9.
1.
2.
3.
RB2011UiAS-RM
RB2011UiAS-RM
Safety Warnings
Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing
accidents.
Ultimate disposal of this product should be handled according to all national laws and regulations.
The Installation of the equipment must comply with local and national electrical codes.
This unit is intended to be installed in the rackmount. Please read the mounting instructions carefully before beginning installation. Failure to use the
correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system.
This product is intended to be installed indoors. Keep this product away from water, fire, humidity or hot environments.
Use only the power supply and accessories approved by the manufacturer, and which can be found in the original packaging of this product.
Read the installation instructions before connecting the system to the power source.
We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your
own risk!
In the case of device failure, please disconnect it from power. The fastest way to do so is by unplugging the power plug from the power outlet.
It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling
requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik devices must be professionally installed.
First use
Choose your powering solution, please see the section for possibilities.Powering
Connect your Internet cable to port 1 (labeled "Internet"), and local network computers to other ports.
Connect your direct input power jack if not using POE, to start up the device.
If using POE please see section on how to connect.POE Adapter
The device will boot up and after the short beep, the network will be available for connecting.
Set your computer IP configuration to automatic (DHCP).
Once connected to the network, open in your web browser to start configuration, since there is no password by default, you http://192.168.88.1
will be logged in automatically . (or, for some models, check user and wireless passwords on the sticker)
We recommend clicking the "Check for updates" button and updating your RouterOS software to the latest version to ensure the best
performance and stability.
Set up your password on the screen that loads.
Powering
The device accepts powering from either the power jack or from the LAN1 Ethernet port:
Direct-input power jack (5.5 mm outside and 2 mm inside diameter, female, pin positive plug) accepts 8-30 V DC (overvoltage protection starts at
30 V).
Eth1 port accepts 8-30 V DC input (at the board; higher voltage needed to compensate for power loss on long cables) from non-standard
(passive) Power over Ethernet injectors. The board does not work with IEEE802.3af compliant 48 V power injectors.
Maximum power consumption 6 W, with attachments 18 W.
Connecting to a POE Adapter
Connect the Ethernet cable from the device to the POE port of the POE adapter.
Connect an Ethernet cable from your LAN to the LAN port of the POE adapter, please mind arrows for data and power flow.
Connect the power cord to the adapter, and then plug the power cord into a power outlet.
Power output

MikroTik RouterBOARD 2011UiAS-RM Specifications

General

CPU	Atheros AR9344
CPU Cores	1
CPU Speed	600 MHz
RAM	128 MB
Storage	128 MB NAND
SFP Ports	1
Operating System	RouterOS
License level	5
Voltage Monitor	Yes
PCB temperature monitor	Yes
Operating temperature	-20°C to 60°C
Architecture	MIPSBE
Wireless	No
USB Ports	1
PoE in	Yes
PoE out	Yes
Power Supply	External

Summary

Safety Warnings and Precautions

General Safety Instructions

Provides essential safety guidelines for handling electrical equipment, installation, and product usage to prevent accidents and damage.

Initial Setup and Operation

First Use Steps

Sequential steps for initial device setup, including powering, network connection, IP configuration, and software updates.

Powering the Device

Powering Options

Details the two accepted powering methods: direct DC input jack and passive Power over Ethernet via the LAN1 port.

Connecting to a PoE Adapter

Step-by-step guide on how to connect the device using a PoE adapter, including cable connections for data and power.

Configuration and Mounting

RouterOS Software Updates

Recommends updating RouterOS for best performance and stability, and selecting the correct country for wireless compliance.

Mounting Instructions

Guidance on mounting the device in a rackmount enclosure, including environmental and grounding considerations.

Device Ports and Slots

Overview of the device's extension slots and ports, including Ethernet, SFP, USB, and serial interfaces.

RouterBOOT Reset Functions

Explanation of the RouterBOOT reset button's functions for configuration reset, clearing, and Netinstall recovery.

Compliance and Included Parts

Included Parts

Lists the essential components included with the device, specifically the 24V 1.2A power adapter.

Operating System Support

Specifies support for RouterOS software version 6 and where to find the factory-installed version number.

FCC Interference Statement

Details FCC compliance, potential radio frequency interference, and user responsibilities for commercial installations.

Canadian Compliance

Information on compliance with Canadian regulations for radio apparatus and digital apparatus (ICES-003).

Regional Compliance Marks

Eurasian Conformity Mark

Explains the Eurasian Conformity Mark (EAC) and provides manufacturer information and warranty service contacts.

Norma Oficial Mexicana

States compliance with the Mexican energy efficiency standard NOM-029-ENER-2017 and operational conditions.

CE Declaration of Conformity

Provides the manufacturer's declaration of conformity to EU directives and the internet address for the full text.