Home
Milnor
Washer
36026V7Z
Milnor 36026V7Z Maintenance Guide
4
of 1
of 1 rating
38 pages
Give review
Manual
Specs
To Next Page
To Next Page
Loading...
Published Manual Number/ECN: MKWOCH01U1/2022035A
• Publishing System: TPAS2
• Access date: 01/13/2022
• Document ECNs: Latest
36021 & 36026V7Z
42026 & 42030V6Z
PELLERIN MILNOR CORPORATION
POST OFFICE BOX 400, KENNER, LOUISIANA 70063-0400, U.S.A.
2
Table of Contents
Table of Contents
8
Machine Description and Identification
11
About this Manual and Your Milnor® Machine
11
Description
11
Machine Identification
11
Machine Data Plate
11
Figure 1 Machine Data Plate
11
Safety
12
Safety - Rigid Washer Extractors
12
Safety Alert Messages-Internal Electrical and Mechanical Hazards
12
Safety Alert Messages-Cylinder and Processing Hazards
12
Safety Alert Messages-Unsafe Conditions
14
Damage and Malfunction Hazards
14
Hazards Resulting from Inoperative Safety Devices
14
Hazards Resulting from Damaged Mechanical Devices
14
Careless Use Hazards
15
Careless Operation Hazards-Vital Information for Operator Personnel (See also Operator Hazards Throughout Manual)
15
Careless Servicing Hazards-Vital Information for Service Personnel (See also Service Hazards Throughout Manuals)
15
Prevent Damage from Chemical Supplies and Chemical Systems
16
How Chemical Supplies Can Cause Damage
16
Dangerous Chemical Supplies and Wash Formulas
16
Incorrect Configuration or Connection of Equipment
16
Figure 2 Incorrect Configurations that Let the Chemical Supply Go in the Ma
17
Equipment and Procedures that Can Prevent Damage
18
Use the Chemical Manifold Supplied
18
Figure 3 Incorrect Configurations that Let the Chemical Supply Go in the Ma
18
Figure 4 Examples of Manifolds for Chemical Tubes. Your Equipment Can Look
18
Close the Line
19
Do Not Let a Vacuum Occur
19
Flush the Chemical Tube with Water
19
Put the Chemical Tube Fully below the Inlet
19
Prevent Leaks
19
Figure 5 a Configuration that Prevents Flow in the Machine When the Pump Is off (if the Chemical Tube and Tank Have no Pressure)
19
Routine Maintenance
20
Maintenance Summary
20
Guards and Related Components
21
Filters, Screens, and Sensitive Components
21
Table 1 Guards and Related Components
21
Table 2 Filters, Screens, and Sensitive Components
21
Components that Become Worn
22
Bearings and Bushings
22
Motor Grease Schedule
22
Mechanisms and Settings
22
Table 3 Components that Become Worn
22
Table 4 Bearings and Bushings
22
How to Remove Contamination
23
Lubricant Identification
24
Grease Gun Procedures
25
Procedures for Bearing Components Connected to a Grease Plate
25
Procedures for Motors
26
Figure 6 Motor Grease Maintenance Conditions
27
How to Show the Maintenance on a Calendar
28
Maintenance Components-Machines and Controls Group
29
How to Examine V-Belts and Pulleys
29
Figure 7 Belt and Pulley Conditions to Look for
29
Figure 8 How to Adjust Belt Tension on a Machine that Uses Spring Tension
30
Inverters
31
Chemical Devices
31
Figure 9 Electric Box and Inverter. These Are Examples. Your Machine Can Look
31
Water and Steam Devices
32
Figure 10 Chemical Inlet Manifolds for Chemical Pump Systems. See Caution
32
Figure 11 Soap Chute and Optional 5-Compartment Supply Injector. These Are Ex
32
Figure 12 Air Tube for the Water Level Sensor. These Are Examples. Your Ma- Chine Can Look Different
33
Figure 13 Water Pressure Regulator for Chemical Flush. These Are Examples
33
How to Examine Compressed Air Mechanisms
34
Figure 14 Steam Inlet Strainer. These Are Examples. Your Machine Can Look Different
34
Figure 15 Compressed Air Inlet Strainers. These Are Examples. Your Machine Can Look Different
34
Figure 16. Self-Purging Air Line Filter to Remove Moisture and Other Contamination. These Are Examples. Your Machine Can Look Different
35
How to Do a Test of Emergency Stop Mechanisms
36
Figure 17 Compressed Air Mechanisms These Are Examples. Your Machine Can Look Different
36
Maintenance Components-Large Extractors
38
Lubricant Maintenance for Grease-Filled Drive Bearings
38
Figure 18 Grease Ports for Grease-Only Bearing Assembly
38
Other manuals for Milnor 36026V7Z
Operator's Guide
110 pages
Service
103 pages
Installation
56 pages
4
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the Milnor 36026V7Z and is the answer not in the manual?
Ask a question
Milnor 36026V7Z Specifications
General
Model
36026V7Z
Category
Washer
Brand
Milnor
Phase
3
Frequency
60 Hz
Motor HP
7.5 HP
Extract G-Force
300 G
Capacity
60 lb (27 kg)
Voltage
200-240V or 380-480V
Related product manuals
Milnor 36026V5J, 36026V7J
118 pages
Milnor 36026V5Z
110 pages
Milnor 36026X8J
165 pages
Milnor 36026X8R
34 pages
Milnor 36021
110 pages
Milnor 36021V5Z
103 pages
Milnor 36021V Series
117 pages
Milnor 36 Series
117 pages
Milnor 30015
34 pages
Milnor 30022H8J
85 pages
Milnor 30022VRJ
99 pages
Milnor 30022V6J
97 pages