Milwaukee 5366-1 - User Manual

Installing Bits (Fig 1.)
This tool is designed with a universal drive system that
accepts SDS, SDS Plus and Hilti-TE-C style bits. Always
clean and lubricate the shank of the bit before installing it
into your tool to help prevent heat build-up and to protect the
bit shank from wear due to abrasive concrete dust.
1. To install a bit, pull
the chuck collar back
toward the tool.
2. Line up the recesses on
the shank of the bit with
the marks on the chuck
collar as shown. Then,
insert the bit into the
spindle as far as possible.
3. Release the chuck col-
lar, locking the bit into
position. Rotate the bit
slightly to be sure it is
locked securely.
4. To remove the bit, pull
the chuck collar back
toward the tool and
remove the bit.
Installing the Side Handle and the Depth Gauge
The tool is shipped with the side handle and depth rod pack-
aged separately.
1.To install the handle assembly, pry open the black handle
ring (wedging the head of a large screwdriver in the handle
ring gap may be helpful) and slip it over the nose of the gear
case, making sure that the molded keys on the inside diame-
ter of the handle ring engage the groove on the gear case.
2. Pass the bolt through the hole in the handle ring and screw
on the red side handle.
3. The depth rod passes through the auxiliary hole in the
handle ring and is clamped in place when the side handle is
tightened. To loosen the rod, partially unscrew the handle as
indicated above.
4. The drilling depth is the distance between the portion of
the bit where the flutes end and the tip of the depth rod (Fig
2.) Slide the depth rod backward or forward until it is set for
the desired depth. Then tighten the side handle securely.
Selecting Drill or Rotary Hammer Action (Fig 3.)
MILWAUKEE 3/4” Rotary Hammers have two settings: rota-
tion only or rotary hammering.
1. To select rotation only, rotate the shift knob 180° in the
direction of the double arrow so that the tab portion of the
knob points toward the “Drill” symbol. Do not shift the tool
when it is running or coasting to a stop.
Milwaukee Tool
Heavy-Duty Falcon Rotary Hammers
Model Numbers: 5366-1, 5368-1, 5368-6 (kit)
Operating Instructions
Page 1
RenTrain INC
RenTrain INC
To reduce the risk of injury, always unplug tool
before attaching or removing accessories. Use
only specifically recommended accessories.
Others may be hazardous.
WARNING!
ASSEMBLY
OPERATION
Fig. 1
Fig. 2
1.
1.
2.
2.
3.
1. Line up the recesses on the
shank...
2. With the marks on the
chuck collar
1. Drilling Depth
2. Tip of Depth Rod
3. Flutes end here

Summary

Assembly and Installation

Installing Bits

Instructions for installing SDS, SDS Plus, and Hilti-TE-C style bits into the rotary hammer. Includes cleaning and lubrication.

Installing Side Handle and Depth Gauge

Guide for attaching the side handle and depth rod to the rotary hammer for proper operation and depth control.

Operating Instructions

Selecting Drill or Rotary Hammer Action

How to choose between 'rotation only' and 'rotary hammering' modes using the shift knob.

Using the Forward;Reverse Switch

Instructions on operating the forward (clockwise) and reverse (counterclockwise) rotation switch for the tool.

Starting, Stopping, and Speed Control

Guidance on how to start, stop, and control the variable speed of the rotary hammer using the trigger.

Rotary Hammering Operation

Techniques for effective rotary hammering, including grip, pressure, and avoiding overload for optimal performance.

Using Rotary Percussion Core Bits

Detailed steps for using core bits with the rotary hammer, including adapter installation and drilling depth.

Milwaukee 5366-1 Specifications

General

Voltage	120V AC
Amperage	10A
Impact Energy	8.1 ft-lbs
Chuck Type	SDS Max
SDS Max Solid Bit Capacity	1-1/4 in
Cord Length	10 ft
SDS Max Core Bit Capacity	4 in