Milwaukee 5311 - User Manual

Installing and Removing Drill Bits and Chisels
(Fig. 1)
For Cat. No. 5313 only
1. Insert the bit or chisel into the nose of the tool.
2.Rotate bit slowly until it aligns with locking mechanism.
3. Push bit into tool until it locks.
4. Check to see that bit is locked by pulling on it.
5. To remove bits and chisels pull bit release collar toward
rear of tool and remove bit.
Use caution when handling hot bits and chisels.
For Cat. No. 5311 & 5316 only
1. Place bit lock in unlocked position.
2. Insert the bit or chisel into the nose of the tool. If you are
using a chisel, make sure that the notch in the shank faces
toward the bit lock.
3.Push the bit lock to the locked position.
4. To remove bits and chisels place bit lock in unlock position
and remove bit or chisel.
Use caution when handling hot bits and chisels.
Adjusting the Side Handle Position (Fig. 2)
Loosen the handle slightly, rotate it to the desired position and
tighten it securely.
Side handle can be used at the rear of the tool. Remove and
install in one of the positions provided on either side. Use the
side handle knob (packaged with the tool) in the front handle
position to secure the depth gauge assembly.
Setting the Depth Gauge (Fig. 3)
1. Loosen the depth rod adjustment knob.
2. Slide the depth gauge rod backward or forward until it is set
for the desired depth. The drilling depth is the distance
between the tip of the bit and the tip of the depth gauge rod.
3. Tighten the depth gauge rod adjustment knob securely.
Milwaukee Tool
1-1/2” Heavy-Duty Rotary Hammers
Model Numbers: 5311, 5313, 5316
Operating Instructions
Page 1
RenTrain INC
RenTrain INC
To reduce the risk of injury, always unplug tool
before attaching or removing accessories. Use
only specifically recommended accessories.
Others may be hazardous.
WARNING!
ASSEMBLY
max
SDS
Fig. 2
Fig. 3
Fig. 1
Handle
Depth gauge rod
adjustment knob
Depth gauge rod
Bit release collar
Bits
Nose
Rear side handle mount

Summary

ASSEMBLY

Installing and Removing Drill Bits and Chisels

Details on inserting, locking, and removing bits/chisels from the tool.

Adjusting the Side Handle Position

Instructions for adjusting the auxiliary handle for improved control and positioning.

Setting the Depth Gauge

OPERATION

Removing the Depth Gauge System from Tool

Steps to detach the depth gauge system from the rotary hammer assembly.

Selecting Action

How to choose between hammering, chisel mode, or rotation with hammering.

Starting, Stopping & Controlling Speed

Guide on operating the trigger for tool control and speed adjustment.

Cold Starting

Procedure for warming up the tool in cold conditions or after long storage.

Operating

General guidance on positioning, grasping, and applying pressure for optimal use.

Using Rotary Percussion Core Bits

Chiseling & Chipping

Bushing Tools

Description of bushing tools used for surfacing concrete.

Mortar Cutting Chisels

Use of mortar cutting chisels for removing old mortar.

Operating Instructions (continued)

Bull Points

Application of bull points for light demolition work.

Cold Chisels

Use of cold chisels for edging, chipping or channeling.

Scaling Chisels

Use of scaling chisels for removing weld spatter or scale.

Slotting Chisel

Use of slotting chisels for cutting between drilled holes.

Setting Self-Drilling Anchors

Procedure for setting self-drilling anchors up to 7/8" using the tool.

Milwaukee 5311 Specifications

General

Type	Rotary Hammer
Voltage	120V
No Load RPM	0-1, 100 RPM
Chuck Type	SDS-Plus
Drilling Capacity (Steel)	1/2 in