To Next PageTo Next Page
Need help?Do you have a question about the Mimosa Backhaul B5-Lite and is the answer not in the manual?
General| Brand | Mimosa |
|---|---|
| Model | Backhaul B5-Lite |
| Category | Network Hardware |
| Language | English |
Provides an overview of frequently asked questions for Mimosa Backhaul.
Explains the default IP addresses for wired and wireless interfaces.
States that Mimosa radios do not respond to CDP or LLDP.
Details the steps to restore B5/B5c and B11 devices to factory settings.
Describes the factory reset procedure for the B5-Lite device.
Explains how to locate the serial number on Mimosa radios.
Guides on obtaining an unlock code for a different country.
Explains MAC throughput and how TDMA settings affect it.
Details maximum transmit power levels for different Mimosa products.
Discusses optimizing Tx power for best performance based on SNR.
Shows SNR requirements for different Modulation and Coding Schemes (MCS).
Describes Error Vector Magnitude (EVM) and its assessment.
Explains Mimosa's QoS queues for traffic prioritization.
Defines link latency and how it's configured with TDMA Window Size.
Discusses factors affecting TCP throughput and performance.
Explains how link distance depends on design requirements and physics.
Describes how Mimosa radios scan spectrum for interference.
Details the feature that automatically adjusts link settings for optimal performance.
Explains the Dual Link feature for routing traffic to the channel with lower PER.
Details the integrated GPS/GLONASS receiver for synchronization.
Provides guidelines for collocating with other radios.
Explains how to connect two Backhaul radios back-to-back.
Outlines compatibility between different Mimosa Backhaul products.
Discusses antenna compatibility for the Mimosa B5c.
Covers antenna compatibility for the Mimosa B11.
Explains how Mimosa Backhaul radios handle Layer 2 bridging and traffic.
Describes VLAN management and passthrough capabilities.
Advises against painting the radio due to warranty voidance.
Lists the supported frequency ranges for Mimosa Backhaul products.
Details the supported channel widths for Mimosa Backhaul radios.
Specifies the frequency tolerance for the B11 product.
Shows receiver sensitivity in dBm for each MCS index.
Covers regulations and product compatibility for the 4.9 GHz band.
Details voltage input and PoE injector output specifications.
Explains IP ratings for B5/B5c and B5-Lite enclosures.
Describes the materials used for gaskets in B5/B5c and B11.
Provides an overview of the installation process for different Mimosa radios.
Guides on obtaining and applying an unlock key for Mimosa radios.
Details the SMS verification process for B5-Lite accounts.
Provides steps for securely mounting and grounding the B5 radio.
Details the procedure for mounting and grounding the B5c radio.
Explains how to mount and ground the B5-Lite radio.
Covers the mounting and grounding process for the B11 radio.
Ensures proper PoE connection to power sources, radios, and the LAN.
Guides on securing and protecting the Ethernet cable with an IP67 gland.
Details the installation of an IP67 gland for the Fiber port.
Ensures secure installation of RF cables to the B5c radio and antenna.
Assists users with preliminary radio setup and link tests before deployment.
Explains how to access the radio's GUI via wireless or Ethernet.
Guides on logging into the device GUI with a password.
Provides an overview of the GUI's title bar, navigation pane, and content pane.
Describes the Dashboard panels for viewing link status and performance.
Explains how to interpret received signal strength indicators.
Details the procedure for aligning antennas using the Aiming Mode screen.
Shows how to read device configuration and status tables.
Explains how to interpret Chains and Streams tables in MIMO status.
Explains how to use the Spectrum Analyzer to report on interference.
Allows automatic or manual changes to frequency, channel width, and power.
Lists frequency ranges where the device should not operate.
Controls for configuring and fine-tuning TDMA performance.
Defines the 5 GHz SSID and passphrase between radios.
Shows settings and metrics between the AP and each client device.
Explains the chart showing GPS/GLONASS satellites for synchronization.
Details values contributing to clock accuracy from satellite signals.
Shows location, altitude, and heading for local and remote devices.
Enter local radio latitude/longitude for distance and map display.
Enter remote radio latitude/longitude for distance and map display.
Calculated distance between radios used for propagation delay.
Summarizes detected APs, their configuration, and capabilities.
Sets local identifiers for administrative purposes.
Shows current UTC date/time and allows setting the install date.
Guides on changing the device password for network protection.
Configures general functionality not described elsewhere.
Controls network addressing, subnet, gateway, and DNS servers.
Monitors a remote host and reboots the local device on failure.
Secures management traffic using SSL and session timeouts.
Controls Mimosa Cloud Management and Ethernet port settings.
Allows changing data port status and speed for the B11.
Enables VLAN for management traffic, requiring a VLAN-capable switch.
Enables remote access to radio's REST API with username and password.
Allows local browser-based configuration via Wi-Fi.
Manages access to the local wireless management network.
Enables SNMP service for requests and push notifications.
Defines which traps are sent to the remote SNMP server.
Enables Syslog service to send traps to a remote Syslog server.
Defines which traps are sent to the remote server for the System Log.
Guides on updating device firmware for stability and performance.
Allows rebooting or resetting the device to factory settings.
Manages configuration settings files via download or upload.
Outlines Ping, Bandwidth, and Traceroute tests for diagnostics.
Allows viewing events and downloading diagnostic information for support.
Allows developers to access hardware information and configuration.
Returns device status information from the embedded Dashboard.
Returns detailed device information from summary tables.
Returns networking information from the Management page.
Returns detailed link information from the Wireless section.
Reboots the device via the REST API.
Provides links to download Mimosa SNMP Management Information Base (MIB) files.
Summarizes available SNMP values and their UI locations.
Retrieves a single management value using SNMP GET requests.
Retrieves a subtree of management values using SNMP GETNEXT requests.
Retrieves an SNMP table and displays it in tabular form.
Substitutes object names for OIDs in SNMP queries.
Categorizes common troubleshooting issues.
Explains the meaning of LED indicators on B5/B5c devices.
Details the meaning of LED indicators on the B5-Lite device.
Explains the LED indicators on B11 devices.
Addresses common Ethernet issues, particularly cabling.
Guides on restoring access after enabling Management VLAN.
Provides checks for radios that become unavailable after a few seconds.
Covers common reasons for radios not associating.
Addresses issues related to GPS signal strength for synchronization.
Troubleshooting steps for low signal-to-noise ratio.
Troubleshooting steps for high packet error rate.
Troubleshooting steps for low transmit/receive power.
Addresses causes of low TCP throughput.
Guides on using iPerf for reliable TCP performance measurement.
Lists released firmware versions and download links.
Provides firmware download links for B5/B5c, B5-Lite, and B11 products.
Explains Frequency Diversity (FD) mode for transmit/receive channels.
Describes Line of Sight (LOS) and Fresnel zones for radio signal analysis.
