For complete product specication and operational guidance,
read the full length user manual at www.minelab.com.
2
2
3
3
4
1
1
3
4
1
2
3
1 2
Getting Started Guide
WARRANTY TERMS
Please refer to www.minelab.com/warranty-conditions
for full warranty terms and conditions. Register your product
warranty online at register.minelab.com
COMPLIANCE
Information to the User (FCC Part 15.105)
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device
must accept any interference received, including interference
that may cause undesired operation.
NOTE: Class B Devices
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit dierent
from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician
for help
Warning: Any changes or modications not expressly approved
by Minelab Electronics could void the user’s authority to operate
this equipment.
+353 21 423 2352
minelab@minelab.ie
North, South & Central America
+1 630 401 8150
minelab@minelab.com
Middle East & Africa
+971 4 254 9995
minelab@minelab.ae
Minelab®, EQUINOX®, Wi-Stream™, Multi-IQ®, 5F×8™ and 3F×3™ are trademarks of Minelab Electronics Pty. Ltd. Images and graphics are for
illustration purposes only; product conguration and specications may vary from those shown. Please refer to the product manual for detailed
operational guidance. The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks
by Minelab is under license. Qualcomm® aptX™ is a product of Qualcomm Technologies International, Ltd.
4901-0248-1-EN
Specications
EQUINOX 600 EQUINOX 800
Detect Modes
Park, Field, Beach
6 × custom search proles
Park, Field, Beach, Gold
8 × custom search proles
Operating Frequencies (kHz) 5, 10, 15, Multi 5, 10, 15, 20, 40, Multi
Standard Headphones 3.5mm / ⁄" (32 ohms) Bluetooth® / aptX™ Low Latency
WM 08 Compatible Yes, WM 08 not included Yes, WM 08 included
Waterproof Waterproof to 3 m (10-feet)
Battery Life (approx.) 12 hours, Full recharge time ≈ 5 hours.
Standard Coil EQX 11 Double-D smart coil
Assembly | Follow the steps to put together your EQUINOX Series detector
2. Assemble shafts
1. Loosen the twistlocks by rotating them
counter-clockwise.
2. Press the spring loaded pin in the lower shaft
and slide it into the middle shaft until the pin
reaches the adjustment holes. The pin will click
into place.
3. Attach the middle shaft to the upper shaft in
the same way.
4. Lock the position of the shafts by rotating
twistlocks clockwise.
3. Attach armrest/stand
1. Place the armrest onto the top of the upper
shaft. Position the armrest just below your
elbow, then line up the central hole in the
armrest with the nearest hole in the shaft.
2. Insert the screw through the stand, upper shaft
and armrest. Tighten the screw carefully.
3. With the velcro side facing upwards, thread
the armrest strap through both slots in the
armrest. Ensure the end of the strap will be
fastened outwards from your arm.
1. Attach coil to lower shaft
1. Insert the two rubber washers into the holes
on either side of the yoke.
2. Slide the yoke into the yoke bracket on top of
the coil.
Ensure that the spring loaded pin in the lower
shaft is underneath.
3. Insert the plastic bolt through the yoke and the
yoke bracket.
4. Fasten with the plastic bolt - Do not
overtighten.
4. Connect coil
1. Wrap the coil cable around the lower and
middle shaft enough times to take up the
slack.
2. Use the velcro tabs provided to secure the coil
cable against the shaft.
3. Align the coil connector and plug into the
socket in the back of the control box, lightly
tightening the retaining ring.
Audio
EQUINOX Series detectors have an external
loudspeaker for detecting without headphones.
A range of other audio options are available. Please
refer to the full instruction manual for further
information, including wireless options.
Charge battery
EQUINOX Series detectors have an internal Li-Ion rechargeable battery. Before rst use, it is recommended
that you fully charge the battery. For fastest charge time, turn the detector o during charging.
1. Connect the magnetic charging cable USB connector to any standard powered USB port.
2. Connect the magnetic charger connector to the socket on the rear of the detector user interface. The
Charge Status LED at the top left of the user interface will ash steadily.
3. When charging is complete, the Charge Status LED will remain on.
Minelab Electronics,
PO Box 35, Salisbury South
South Australia 5106
To Next Page
Need help?
General
