To Next PageTo Next PageWhat to do if operation mode is not changed properly on Mitsubishi Electric FR-S520SE-0.4K Inverter?
If the operation mode is not changing correctly on your Mitsubishi Electric Inverter, ensure that the STF or STR signal is off. Check the Pr. 79 setting and make sure that the connector is fitted securely across terminals P-P1.
How to reduce annoying sound from Mitsubishi Electric Inverter motor?
To reduce annoying sounds from your Mitsubishi Electric Inverter motor, check the Pr. 70 "Soft-PWM setting". Also, make sure that the deceleration time is not too short.
Why is Mitsubishi Electric Inverter motor rotating in opposite direction?
If your Mitsubishi Electric Inverter motor is rotating in the opposite direction, check that the phase sequence of the output terminals is correct. Also, check the setting of Pr. 17 "RUN key rotation direction".
Why does the speed not increase on my Mitsubishi Electric FR-S520SE-0.4K Inverter?
If the speed on your Mitsubishi Electric Inverter is not increasing, verify that the maximum frequency setting is not set to zero. Also, check to see if the load is too heavy.
What to do if Mitsubishi Electric FR-S520SE-0.4K motor remains stopped?
If your Mitsubishi Electric Inverter motor remains stopped, check if the main circuit display is active and the motor is properly connected. Ensure the jumper across P-P1 is connected and that the start signal is being input. Also, confirm that the frequency setting signal is not zero and the operation mode (Pr. 79) setting is correct. Finally, verify that the load isn't too heavy and the shaft isn't locked.
How to fix unsmooth acceleration/deceleration on Mitsubishi Electric FR-S520SE-0.4K Inverter?
To address unsmooth acceleration or deceleration on your Mitsubishi Electric Inverter, verify that the acceleration and deceleration time settings are correct. Also, check if the load is too heavy.
Why does the speed greatly differ from the setting on my Mitsubishi Electric FR-S520SE-0.4K Inverter?
A significant difference between the set speed and the actual speed of your Mitsubishi Electric Inverter can occur if the frequency setting signal is incorrect. Also, check the parameter settings for Pr. 38, Pr. 39, Pr. 95, C2 to C7. Ensure that the input signal lines are not affected by shielded cables.
Why does the speed vary during operation of my Mitsubishi Electric FR-S520SE-0.4K?
The speed variation during operation of your Mitsubishi Electric Inverter may be due to several factors: a varying load, a fluctuating frequency setting signal, noise affecting the frequency setting signal, a malfunction caused by undesirable current when a transistor output unit is connected, an excessively long wiring length or a small GD[2] load. You can also try setting the Pr. 72 "PWM frequency selection" to 6kHz or higher.
General| Model | FR-S520SE-0.4K |
|---|---|
| Rated Power | 0.4 kW |
| Input Voltage | 200-240 VAC |
| Output Current | 2.5 A |
| Output Frequency | 0.5-400 Hz |
| Control Method | V/f Control |
| Input Frequency | 50/60 Hz |
| Protection Class | IP20 |
| Cooling Method | Fan cooled |
| Output Voltage | 0-240V AC |
Provides detailed diagrams and specifications for connecting inverter terminals.
Explains the layout and function of main circuit terminals for power input and output.
Details the usage and wiring of control circuit terminals for signals and commands.
Outlines methods for implementing failsafe mechanisms to ensure system safety during inverter operation.
Lists all available functions and their corresponding parameter numbers for inverter configuration.
Provides detailed explanations for various inverter functions and their associated parameters.
Lists and describes various error codes and alarm indications for troubleshooting inverter faults.
Provides diagnostic steps and solutions for common motor and inverter operational issues.
Important safety precautions and procedures for performing regular maintenance and inspections on the inverter.
