Mitsubishi Electric MELSEC-Q QD75M - Page 853

Index - 8
Simultaneous starting axis start data No. (Axis 3
start data No.)(
Cd.32
).............................. 5-156
Simultaneous starting axis start data No. (Axis 4
start data No.)(
Cd.33
).............................. 5-156
Skip command (
Cd.37
)............................ 5-158
Skip function................................................ 12-61
Skip operation program................................. 6-47
Slot................................................................... 2-6
Software stroke limit function...................... 12-29
Software stroke limit lower limit value (
Pr.13
)
....................................................................... 5-28
Software stroke limit selection (
Pr.14
)..... 5-28
Software stroke limit upper limit value (
Pr.12
)
....................................................................... 5-28
Software stroke limit valid/invalid setting (
Pr.15
)
....................................................................... 5-28
S-pattern acceleration/deceleration processing
method......................................................... 12-82
S-pattern proportion (
Pr.35
)...................... 5-38
Special start instruction (
Da.13
) .............. 5-101
Special start data instruction code setting value
(
Md.36
)...................................................... 5-130
Special start data instruction parameter setting
value (
Md.37
)............................................ 5-130
Special start repetition counter (
Md.41
)... 5-132
Specifications of input/output interfaces....... 3-18
Specifications of input/output signals ........... 3-14
Speed change 0 flag ................................... 5-126
Speed change function ............................... 12-37
Speed change program ................................ 6-43
Speed change request (
Cd.15
) ............... 5-107
Speed designation during OP shift (
Pr.56
)
....................................................................... 5-56
Speed differential compensation (
Pr.138
).. 5-76
Speed integral compensation (
Pr.117
)....... 5-64
Speed integral compensation changing ratio
(
Pr.155
)........................................................ 5-80
Speed limit function..................................... 12-23
Speed limit value (
Pr.8
) ............................ 5-26
Stop command processing for deceleration
stop selection (
Cd.42
)............................... 5-138
Speed loop gain 1 (
Pr.114
)......................... 5-64
Speed loop gain 2 (
Pr.116
)......................... 5-64
Speed loop gain changing ratio (
Pr.154
).... 5-78
Speed-position function selection (
Pr.200
). 5-32
Speed switching mode (
Pr.19
)..................5-32
Speed-position switching control (ABS mode)
........................................................................9-91
Speed-position switching control (INC mode)
........................................................................9-86
Speed-position switching control movement
amount change register (
Cd.23
) ..............5-152
Speed-position switching control positioning
amount (
Md.29
).........................................5-124
Speed-position switching enable flag (
Cd.24
)
......................................................................5-152
Speed-position switching latch flag.............5-126
Speed-position switching signal ....................3-18
Spiral interpolation .........................................9-61
SSCNET........................................................ A-14
SSCNET cable over all length.........................3-3
Standard speed switching mode...................9-12
Start Hour (
Md.5
) ......................................5-112
Start complete signal .....................................3-15
Start data No. (
Da.12
) ..............................5-101
Start data pointer being executed (
Md.43
)
......................................................................5-132
Start details setting program..........................6-54
Start history..................................................5-112
Start history pointer (
Md.8
) .......................5-114
Start information (
Md.3
)............................5-112
Start Minute: second (
Md.6
).....................5-112
Start No. (
Md.4
).........................................5-112
Start positioning data No. setting value
(
Md.38
)......................................................5-130
Start program .................................................6-56
Start program for high-level positioning control
......................................................................10-23
Status (
Md.31
)...........................................5-126
Step function................................................12-56
Step mode....................................................12-57
Step mode (
Cd.34
)...................................5-156
Step operation program.................................6-46
Step start information...................................12-58
Step start information (
Cd.36
)..................5-158