24
en
4.11 Using SD memory card
FTC is equipped with an SD memory card interface.
Using an SD memory card can simplify main remote controller settings and can
store operating logs. *1
(a) For insertion, push on the SD memory card until it clicks into place.
(b) For ejection, push on the SD memory card until it clicks.
Note: To avoid cutting ngers, do not touch sharp edges of the SD
memory card connector (CN108) on the FTC control board.
Logos
Capacities
2 GB to 32 GB *2
SD speed classes
All
• The SD Logo is a trademark of SD-3C, LLC.
The mini
SD logo is a trademark of SD-3C, LLC.
The micro SD logo is a trademark of SD-3C, LLC.
*1 To edit main remote controller settings or to check operating data, an Ecodan
service tool (for use with PC) is required.
*2 A 2-GB SD memory card stores up to 30 days of operation logs.
<Handling precautions>
(1) Use an SD memory card that complies with the SD standards. Check that the
SD memory card has a logo on it of those shown to the right.
(2) SD memory cards to the SD standards include SD, SDHC, mini SD, micro SD,
and micro SDHC memory cards. The capacities are available up to 32 GB.
Choose that with a maximum allowable temperature of 55ºC.
(3) When the SD memory card is a mini SD, mini SDHC, micro SD, or micro SDHC
memory card, use an SD memory card converter adapter.
(4) Before writing to the SD memory card, release the write-protect switch.
system. If an SD memory card is inserted or ejected with the system powered
on, the stored data could be corrupted or the SD memory card be damaged.
insertion or ejection wait until the LED lamps on the FTC control board are all
-
ory cards, however, these operations are not always guaranteed as the speci-
Manufacturer Model Tested in
Verbatim #44015 Mar. 2012
SanDisk SDSDB-002G-B35 Oct. 2011
Panasonic RP-SDP04GE1K Oct. 2011
Arvato 2GB PS8032 TSB 24nm MLC Jun. 2012
Arvato 2GB PS8035 TSB A19nm MLC Jul. 2014
SanDisk SDSDUN-008G-G46 Oct. 2016
Verbatim #43961 Oct. 2016
Verbatim #44018 Oct. 2016
VANTASTEK VSDHC08 Sep. 2017
Before using a new SD memory card (including the card that comes with the
unit), always check that the SD memory card can be safely read and written to
by the FTC controller.
<How to check read and write operations>
a) Check for correct wiring of power supply to the system. For more details,
refer to section 4.1.
(Do not power on the system at this point.)
b) Insert an SD memory card.
c) Power on the system.
d) The LED4 lamp lights if the read and write operations are successfully
completed. If the LED4 lamp continues blinking or does not light, the SD
memory card cannot be read or written to by the FTC controller.
(7) Make sure to follow the instruction and the requirement of the SD memory
card’s manufacturer.
(8) Format the SD memory card if determined unreadable in step (6). This could
make it readable.
Download an SD card formatter from the following site.
SD Association homepage: https://www.sdcard.org/home/
(10) Mitsubishi Electric is not liable for any damages, in whole or in part, including
failure of writing to an SD memory card, and corruption and loss of the saved
data, or the like. Back up saved data as necessary.
(11) Do not touch any electronic parts on the FTC control board when inserting or
ejecting an SD memory card, or else the control board could fail.
4. Electrical work
(a)
(b)
FTC (Main)
FTC (Sub)
(a)
(b)
To Next Page
Loading...
