To Next PageTo Next PageWhy is there no airflow when starting DRY operation on Mitsubishi Heavy Industries SRF35ZJX-S Air Conditioner?
If airflow isn't expelled when starting the DRY operation on your Mitsubishi Heavy Industries Air Conditioner, wait, as the indoor fan may stop.
Why isn't my Mitsubishi Heavy Industries SRF35ZJX-S blowing air when heating?
If airflow isn't expelled when starting the HEATING operation on your Mitsubishi Heavy Industries Air Conditioner and the RUN light blinks slowly, allow 2 to 5 minutes for the indoor heat exchanger to warm up.
How to improve poor cooling or heating in my Mitsubishi Heavy Industries Air Conditioner?
If your Mitsubishi Heavy Industries Air Conditioner isn't cooling or heating well, make sure the thermostat is set to a suitable temperature, the air filter is clean, and all doors and windows are closed.
Why is my Mitsubishi Heavy Industries Air Conditioner not cooling or heating properly?
If your Mitsubishi Heavy Industries Air Conditioner isn't cooling or heating well, first, adjust the thermostat to a more suitable temperature. Also, check to ensure the air filter is clean and that all doors and windows are closed.
Why is there moisture on the Mitsubishi Heavy Industries SRF35ZJX-S outlet grills?
If moisture forms on the air outlet grills of your Mitsubishi Heavy Industries Air Conditioner, it may be because the unit is operated for a long time in high humidity, causing moisture to form and start dripping.
Why does the RUN light stay on after stopping my Mitsubishi Heavy Industries SRF35ZJX-S?
If the RUN light stays on even though operation was stopped on your Mitsubishi Heavy Industries Air Conditioner, the RUN light illuminates during CLEAN operation and turns off when CLEAN operation ends.
Why no airflow when starting DRY operation on my Mitsubishi Heavy Industries SRF35ZJX-S?
If airflow is not blown out when starting the DRY operation of your Mitsubishi Heavy Industries Air Conditioner, the indoor fan may stop to prevent re-evaporation of dehumidified moisture and to save energy.
Why is my Mitsubishi Heavy Industries SRF35ZJX-S Air Conditioner not cooling effectively?
If your Mitsubishi Heavy Industries Air Conditioner isn't cooling well, check if there is direct sunlight entering the room, if there is a heat source in the room, or if there are too many people in the room.
Why does my Mitsubishi Heavy Industries SRF35ZJX-S Air Conditioner blow cold air during heating?
If your Mitsubishi Heavy Industries Air Conditioner has airflow that is not blown out for 5 to 10 min, or blows out not warm wind for a moment at HEATING operation, and the RUN light blinks slowly, the unit is likely defrosting automatically because the outdoor temperature is low and humidity is high. Please wait.
Why is there no airflow when starting the heating on my Mitsubishi Heavy Industries SRF35ZJX-S?
If your Mitsubishi Heavy Industries Air Conditioner is not blowing airflow when starting the HEATING operation and the RUN light blinks slowly, it's likely stopped to prevent cold air from blowing until the indoor heat exchanger warms up, which usually takes 2 to 5 minutes.
General| Cooling Capacity | 3.5 kW |
|---|---|
| Heating Capacity | 4.0 kW |
| Indoor Unit Dimensions (W x H x D) | 845 x 275 x 228 mm |
| Outdoor Unit Dimensions (W x H x D) | 780 x 540 x 269 mm |
| Refrigerant | R32 |
| Energy Efficiency Ratio (EER) | 3.50 |
| Power Supply | 220-240V, 50Hz |
| Energy Efficiency Ratio (Cooling) | 3.50 |
Important safety measures to follow during installation.
Critical safety guidelines for using the air conditioner.
Further safety advice for operation and handling.
Safety guidelines for moving or repairing the unit.
Identifies and describes components of the indoor unit.
Details parts visible when the air inlet panel is removed.
Explains the buttons and indicators on the remote control.
Lists and describes the items included with the air conditioner.
Instructions for changing batteries and using the remote holder.
Addresses issues with remote control operation and temporary use.
Details the function of each button and the display elements.
Guides users on how to set the current time on the remote.
Explains automatic mode selection based on room temperature.
How to adjust the fan speed for different operating conditions.
How to select and adjust settings for COOL, HEAT, DRY, and FAN modes.
Details the mechanism, capacity, and defrosting of the heating mode.
How to adjust the up/down airflow direction and memory function.
Instructions for manually adjusting the left/right airflow fins.
Setting both sleep and on timers simultaneously for flexible scheduling.
Setting recurring daily timer operations for convenience.
Explains how to use high power for quick cooling/heating and economy for energy saving.
How to activate the self-cleaning function to remove moisture and control mold.
Advice for economical and comfortable use, including auto-restart.
How to select between upper and lower air outlets.
Explains how air outlets adjust automatically in different modes.
Instructions on how to open, close, remove, and install the air inlet panel.
Steps for cleaning the air filters to maintain performance and efficiency.
Steps to take when preparing the unit for storage at the end of the season.
Tasks to perform before starting the unit at the beginning of a new season.
Details the types of air-cleaning filters and their specific functions.
Advice on selecting the correct position and considerations for installation.
Steps to check when the unit does not work or has cooling/heating problems.
Situations requiring immediate dealer assistance due to safety or malfunction.
Guidelines for using multiple air conditioners simultaneously, including automatic modes.
Explains error codes indicated by light flashes and their causes.
