1
Printed in Japan
Date of publication: February 1, 2019
Safety Precautions
Use this product in conformance with the specications, functions, and
precautions for use described in this document. Failure to do so may impair
your safety.
Foreword
To obtain the highest performance and the longest service life from this
product, carefully read this document thoroughly prior to setup and operation.
After reading, retain it close at hand for future reference. Be sure to follow the
precautions below.
Export Control Compliance
This product is subject to the "Foreign Exchange and Foreign Trade Act"
of Japan. Contact Mitutoyo for re-export and re-sale of the product, or re-
provisioning of the technology.
Electromagnetic Compatibility (EMC)
This product complies with the EMC Directive. Note that, in environments
where electromagnetic interference exceeds the EMC requirements dened
in this directive, appropriate countermeasures are required to ensure product
performance.
Disposal of Old Electrical & Electronic
Equipment (Applicable in the European Union
and Other European Countries with Separate
Collection Systems)
This symbol on the product or on its packaging is based on
WEEE Directive (Directive on Waste Electrical and Electronic
Equipment), which is a regulation in EU member countries, and
this symbol indicates that this product shall not be treated as
household waste.
To reduce the environmental impact and minimize the volume of
landlls, please cooperate in reuse and recycle.
For how to dispose of the product, please contact your dealer or
the nearest Mitutoyo sales ofce.
China RoHS Compliance Information
产品中有害物质的名称及含量
部件名称
有害物质
铅 汞 镉 六价铬 多溴联苯
多溴二苯
醚
(Pb) (Hg) (Cd)
(Cr(VI))
(PBB) (PBDE)
本体
× ○ ○ ○ ○ ○
配件
○ ○ ○ ○ ○ ○
本表格依据 SJ/T 11364 的规定编制。
○ ： 表示该有害物质在该部件所有均质材料中的含量均在 GB/T
26572 规定的限量要求以下。
× ： 表示该有害物质至少在该部件的某一均质材料中的含量超出
GB/T 26572 规定的限量要求。
环保使用期限标识，是根据电器电子产品有害物质限制使用管理办
法以及、电子电气产品有害物质限制使用标识要求（SJ/T11364-
2014）、制定的适用于中国境内销售电子电气产品的标识。
电子电气产品只要按照安全及使用说明内容，正常使用情况下，从
生产月期算起，在此期限内，产品中含有的有毒有害物质不致发生
外泄或突变，不致对环境造成严重污染或对其人身、财产造成严重
损害。
产品正常使用后，要废弃在环保使用年限内或者刚到年限的产品时，
请根据国家标准采取适当的方法进行处置。
另外，此期限不同于质量/ 功能的保证期限。
CONVENTIONS USED IN THIS DOCUMENT
Indicates a potentially hazardous situation which, if not
avoided, could result in serious injury or death.
Indicates a potentially hazardous situation which, if not
avoided, may result in property damage.
Indicates that grounding needs to be implemented.
Precautions for Use
Do not remove the cover or disassemble the product. Otherwise you may be
subject to electric shock, and there is a risk of breakage or re due to a short
circuit caused by metallic powders that have gotten inside the product.
y
This product is precision equipment. Be careful not to apply excessive
shock or force to any of the parts.
y
Use this product in an environment where the temperature is between
0
°C
and 40
°C
and where it will be subject to minimal temperature
change without condensation.
y
Avoid using this product in the following places:
–
Places exposed to chips, machining oil, dust, and vibration.
–
Places subject to direct sunlight.
–
Around devices that use high voltage or current.
Warranty
In the event that this product should prove defective as a result of
workmanship, material or transportation, within 1 year from the date of original
purchase, it will be repaired free of charge. Contact your dealer or the nearest
Mitutoyo sales ofce/service center for repair.
1
Overview
1.1
Major Functions
This product is a Counter that displays the counter values from connected
Mitutoyo Linear Gages. The following main functions are available.
y
Preset, Tolerance Judgment
y
Communication with a PC or external devices via the I/O connector
1.2
Supported Linear Gages
The following table shows the Linear Gages supported by this product and
their features:
Model No.
Supported Linear
Gages
Feature
EG-101P
LGF-L-B, LGK,
LGB, LGB2, LG,
etc.
y
Differential square-wave output type
y
High resolution down to 0.1 µm
y
High-speed response of 1.5 m/s
(LGF)
EG-101Z
LGF-ZL-B, etc.
y
Scale reference-point signal output
type (The origin can be restored even
if the power is turned off)
EG-101D
LGD, LGS, etc. (ID
and SD are also
supported)
y
Digimatic output type
y
ABS function (no need for master
setting)
Tips
Counter values will not be displayed correctly on the Counter in the following cases.
• If the gage that is connected displays a counter value that is more than 6 digits
(whole-number digits + fractional digits).
• If the resolution (minimum reading) is 0.1 mm or more and less than 1 mm.
Linear Gage Counter EG-101P/EG-101Z/EG-101D
No. 99MBC088B9
User's Manual
To Next Page
General