MOONEY INTERNATIONAL CORPORATION
M20V SERVICE AND MAINTENANCE MANUAL
Page
Date
13
MAR 2017
Rev Date
Cleaning
It is recommended that AAIR components be cleaned
on a regular (annual) basis. Build- up of dirt and
debris could interfere with system operation, shorten
the life of the system, and cause corrosion of metal
parts. Surface clean the belt assembly, hoses, cables,
inflator assembly, and EMA.
-NOTE-
Equivalent alternatives are permitted for the
equipment and materials in this list. Qty Descrip-
tion Part Number
QTY
DESCRIPTION PART NUMBER
AR Warm water in a
spill- resistant con-
tainer
Standard Issue
AR Soft lint- free wash-
ing cloth
Standard Issue
AR Sponge or soft brush Standard Issue
AR Mild soap Standard Issue
(household dishwa-
ter liquid soap,
household laundry
detergent)
AR Garrett’s Delicate
Detergent and Gar-
rett’s Nutrient Cream
Garrett Leather
1360 Niagara Street
Buffalo, NY 14213
1- 800- 342- 7738
Intn’l Customers
(716) 882- 9301
AR Isopropyl Alcohol Standard Issue
-WARNING-
DO NOT SOAK PARTS TO BE CLEANED WITH
EITHER WATER SOLUTION OR ISOPROPYL
ALCOHOL. DOING SO MAY DAMAGE THE AAIR
SYSTEM.
-CAUTION-
THE BELT ASSEMBLY MUST NOT BE DRY
CLEANED OR IMMERSED IN WATER.
-CAUTION-
AVOID EXCESSIVE USE OF WATER WHEN
CLEANING. MOISTURE MAY DAMAGE INTER-
NAL COMPONENTS AND CAUSE COMPONENT
FAILURE.
-CAUTION-
WHEN CLEANING THE AAIR, CARE MUST BE
TAKEN TO KEEP FOREIGN MATTER AND
CLEANING MEDIA AWAY FROM THE HARD-
WARE ASSEMBLIES.
-CAUTION-
NO SOAP OR WATER I S TO BE USED ON
METAL PARTS.
-CAUTION-
WHEN USING ISOPROPYL ALCOHOL, AVOID
ANY CONTACT WITH THE WEBBING, AIRBAG
COVER, OR GAS HOSE MATERIAL.
When cleaning non- metallic parts (except airbag cov-
er), use warm water and household soap/laundry de-
tergent. Care should be taken to use only enough
cleaning agent to produce minimal suds. Apply clean-
ing solution with a damp (wrung- out) washing cloth. Do
not leave residue on cleaned areas. Rinse, if neces-
sary, with clear water on a damp (wrung- out) washing
cloth. Hand- wash the webbing and gas hose. Gentle
scrubbing with a soft brush and cold soapy solution is
permissible. Air dry the belt assembly. Do not dry the
belt assembly in sunlight or near any source of heat.
For airbag cover cleaning, please refer to Garrett
Leather’s specific instructions listed on using their
cleaning/conditioning products. In general, gently dust
area regularly with a dry, soft cloth. For cleaning, hand
wash with Garrett’s Delicate Detergent and clear, luke-
warm water. Blot excess liquid immediate with a clean
absorbent cloth or sponge. Allow to air dry. DO NOT dry
wet areas with heat dryers or hair dryers, etc. DO NOT
SOAK leather cover with soapy solution. It is recom-
mended that Garrett’s Nutrient Cream be used after
cleaning- following manufacturer’s directions. Condi-
tion leather airbag cover after it is clean and dry. Proper
care and cleaning of the leather cover are critical to the
longevity of the airbag cover
If necessary, clean the airbag hardware with a lint- free
cloth moistened with isopropyl alcohol.
If cleaning of the EMA is required, cover cable opening
into the EMA with pieces of cloth.
Hand- wash the Inflator and cables with a lint- free cloth
moistened with a cold water/mild soap solution
REMOVAL AND REPLACEMENT
These maintenance instructions provide the necessary
detail to remove and replace the AAIR V23 System.
25-10-03
To Next Page
Loading...
