Motak MR10-RGB24 User Manual (English)

Questions and Answers:

M
Manuel CummingsAug 9, 2025
What to do if the pilot flame is on, but the main burner will not ignite on my Motak MR10-RGB24?
- R
  Rachel OchoaAug 10, 2025
  If the pilot flame is on but the main burner on your Motak Ranges won't ignite, it could be due to several reasons. First, the gas pressure might be insufficient; in this case, adjust the pressure regulator to the proper pressure setting using a manometer, referring to the data tag. Alternatively, the main burner orifice could be blocked, requiring you to unblock it. A defective gas control valve could also be the culprit, necessitating its replacement. Finally, an incorrect by-pass setting could be the cause, so try resetting it.
M
Michael HodgesAug 16, 2025
Why the pilot flame cannot be ignited on my Motak MR10-RGB24 Ranges?
- W
  Wayne RodriguezAug 17, 2025
  If the pilot flame on your Motak Ranges cannot be ignited, several factors could be responsible. First, the gas pressure might be insufficient, requiring you to adjust the pressure regulator to achieve proper pressure. Second, the nozzle might be blocked, so try unblocking it. A loose thermocouple connection could also be the reason; ensure you tighten it. If the thermocouple is defective, it will need replacement. Lastly, a malfunctioning gas control valve may be the cause, necessitating its replacement.
X
xloweryAug 25, 2025
How to fix burners with yellow tips and black soot on Motak Ranges?
- D
  Donna OnealAug 26, 2025
  If the burners on your Motak Ranges have yellow tips and are creating black soot, it could be due to several reasons. The burner orifice might not be the correct size for the type of gas being supplied, so check the orifice size to ensure it is correct for the gas supply. Also, the air shutter might not be adjusted properly, so adjust the air shutter on the burner. Insufficient gas pressure could be a factor, so use a manometer to adjust the pressure regulator to the proper pressure setting on the data tag. Finally, the volume of gas being supplied might be too low; verify that the connection type is at least ¾” inside diameter and of commercial grade, and check with your installer for correction.
K
Kenneth MezaAug 31, 2025
What to do if Motak MR10-RGB24 Ranges burner has a “Pop” sound when gas supply is turned off?
- W
  wcooperSep 1, 2025
  If your Motak Ranges burner makes a “Pop” sound when the gas supply is turned off, there are several potential causes. The burner orifice might not be the correct size for the type of gas being supplied; in this case, check the orifice size to be sure it is correct for the gas supply. Alternatively, the air shutter might not be adjusted properly; adjust the air shutter on the burner. Insufficient gas pressure could also be the cause; use a manometer to adjust the pressure regulator to the proper pressure setting on the data tag. Lastly, the gas supply connection might not be the correct size; verify that the connection type is at least ¾” inside diameter and of commercial grade, and check with your installer for correction.

Motak MR10-RGB24 Specifications

General

Brand	Motak
Model	MR10-RGB24
Category	Ranges
Language	English

Summary

Safety and Standards

Codes and Standards

Details on regulations and codes for installation and operation of the appliance.

General Warnings

Critical safety warnings regarding modification, operation by unqualified persons, and fire hazards.

Gas Leak Detection

Recommended methods for detecting gas leaks using soapy water or a detector, avoiding open flames.

Specifications and Installation

Specifications

Technical details of the range models, including dimensions, capacity, BTU ratings, and gas pressure.

Installation Guidelines

Instructions for proper site selection, ventilation, leveling, and gas connection procedures.

Gas Piping and Regulator

Requirements for gas piping size, joint compound, and regulator connection for safe gas supply.

Manual Shut-Off Valve

Mandates installation of an accessible manual gas shut-off valve upstream of the appliance.

Operation

Control Panel Overview

Identifies and explains the functions of the control panel components for operating the unit.

Burner and Griddle Operation

Guides on lighting pilots, igniting burners, adjusting flame, and preheating/seasoning the griddle.

Oven Operation

Steps for preparing, igniting, and operating the oven, including burn-off and temperature settings.

Maintenance and Troubleshooting

Routine Inspection

Daily checks recommended to ensure safe operation and prevent potential accidents or damage.

Cleaning Procedures

Guidelines for cleaning the range body, burners, and griddle plate to maintain performance and appearance.

Troubleshooting Common Issues

A guide to diagnosing and resolving common problems like pilot ignition or burner issues with their causes and solutions.

Related product manuals

Motak MR10-RGB24 User Manual

Table of Contents

Questions and Answers:

Motak MR10-RGB24 Specifications

Summary

Safety and Standards

Codes and Standards

General Warnings

Gas Leak Detection

Specifications and Installation

Specifications

Installation Guidelines

Gas Piping and Regulator

Manual Shut-Off Valve

Operation

Control Panel Overview

Burner and Griddle Operation

Oven Operation

Maintenance and Troubleshooting

Routine Inspection

Cleaning Procedures

Troubleshooting Common Issues

Related product manuals