Multiplex EasyStar II - Page 17

17
Part No. Description Material Dimensions
1 1 Building instructions, KIT
1.1 1 Complaints form, models
2A 1 Decal sheet „A“ Printed self-adhesive film 200 x 820mm
2B 1 Decal sheet „B“ Printed self-adhesive film 200 x 700mm
3 1 L.H. fuselage shell Moulded Elapor foam Ready-made
4 1 R.H. fuselage shell, with fin Moulded Elapor foam Ready-made
5 1 Canopy Moulded Elapor foam Ready-made
6 1 Tailplane Moulded Elapor foam Ready-made
7 1 L.H. wing panel Moulded Elapor foam Ready-made
8 1 R.H. wing panel Moulded Elapor foam Ready-made
9 1 L.H. joiner channel cover Moulded Elapor foam Ready-made
10 1 R.H. joiner channel cover Moulded Elapor foam Ready-made
11 1 L.H. servo well cover Moulded Elapor foam Ready-made
12 1 R.H. servo well cover Moulded Elapor foam Ready-made
Small parts set
20 3 Velcro tape, hook Plastic 25 x 60 mm
21 3 Velcro tape, loop Plastic 25 x 60 mm
22 4 „Twin“ control surface horn Plastic Ready-made
23 4 Swivel barrel Metal Ready-made, 6 mm Ø
24 4 Allen-head grubscrew Metal M3 x 3 mm
25 1 Allen key Metal 1.5 mm A/F
26 2 Pre-formed aileron pushrod Metal 1 Ø x 80 mm
27 2 Latch catch Inj.-moulded plastic Ready-made
28 2 Latch tongue Inj.-moulded plastic Ready-made
29 2 Cable holder Inj.-moulded plastic Ready-made
30 3 Screw (motor cowl) Metal 2.2 x 6.5 mm
Plastic parts set
40 1 Firewall Inj.-moulded plastic Ready-made
41 1 Motor cowl Inj.-moulded plastic Ready-made
42 1 Cowl screw support Inj.-moulded plastic Ready-made
43 2 Servo mount, „Nano“, upright Inj.-moulded plastic Ready-made
44 1 Tailplane clip Inj.-moulded plastic Ready-made
45 1 Upper tailplane sleeve Inj.-moulded plastic Ready-made
46 1 Lower tailplane sleeve Inj.-moulded plastic Ready-made
47 1 Tailplane frame Inj.-moulded plastic Ready-made
48 1 Tailplane slider Inj.-moulded plastic Ready-made
Wire / rod set, wing joiner
50 1 Wing joiner GRP tube 8.0 Ø x 5.4 x 579 mm
51 2 Pre-formed pushrod, ele. / rud. Metal 0.8 Ø x 620 mm
52 2 Snake inner tube, ele. / rud. Plastic 2/1 Ø x 550 mm
53 3 Snake outer sleeve, elevator Plastic 3/2 Ø x 950 mm
Propeller, driver, spinner set, EasyStar II
55 1 Propeller boss Plastic Ready-made
56 1 Spinner Plastic 35 mm Ø
57 2 Folding propeller blade Plastic 7 x 6"
58 1 Propeller driver, taper collet Metal 3.2 Ø / M6 / hex-head, 13
A/F
59 1 Washer Metal 6.4 I.D.
60 2 Pan-head self-tapping screw Metal 2.2 Ø x 6.5 mm
61 1 O-ring Plastic 30 Ø x 1.5 mm
62 2 Dowel pin Metal 3 Ø x 14 mm
63 1 Nut Metal M6
64 1 Shakeproof washer Spring steel 6.4 I.D.
66 1 Taper collet Metal 3.0 Ø / M6 / hex-head, 13
A/F