Multiplex MENTOR - Page 8

29
Mentor KIT
PartNo. Description Material Dimensions
No. off
1 1 Building instructions Paper, 80 g/m² A4
2 1 Decal set Printed adhesive film 700 x 1000 mm
3 1 L.H. fuselage shell Moulded Elapor foam Ready made
4 1 R.H. fuselage shell Moulded Elapor foam Ready made
5 1 Fuselage insert, aero-tow mechanism Moulded Elapor foam Ready made
6 1 Canopy Moulded Elapor foam Ready made
7 1 L.H. wing panel Moulded Elapor foam Ready made
8 1 R.H. wing panel Moulded Elapor foam Ready made
9 1 L.H. wing spar cover Moulded Elapor foam Ready made
10 1 R.H. wing spar cover Moulded Elapor foam Ready made
11 1 Tailplane Moulded Elapor foam Ready made
12 1 Fin Moulded Elapor foam Ready made
13 1 Spinner Moulded Elapor foam Ready made
60 1 Main undercarriage unit Aluminium Ready made
Small items
20 3 Velcro tape, “mushroom” Plastic 25 x 60 mm
21 3 Velcro tape, “felt” Plastic 25 x 60 mm
22 2 Canopy latch Inj. moulded plastic Ready made
23 2 Canopy latch tongue Inj. moulded plastic Ready made
24 4 Glue-fitting control surface horn Inj. moulded plastic Ready made
25 4 Swivel pushrod connector Metal Ready made, 6 mm Ø
26 4 Washer Metal M2
27 4 Nut Metal M2
28 4 Socket-head grubscrew Metal M3 x 3 mm
29 1 Allen key Metal 1.5 mm A/F
30 2 Aileron pushrod, one Z-bend Metal 1 Ø x 80 mm
31 2 Wing retainer strap Inj. moulded plastic Ready made
32 4 Wing retainer screw Plastic M5 x 60 mm
33 2 Wing screw support A Inj. moulded plastic Ready made, M5
34 2 Wing screw support B Inj. moulded plastic Ready made, M5
35 2 Motor mount Inj. moulded plastic Ready made
36 1 Motor bulkhead Inj. moulded plastic Ready made
37 4 Motor bulkhead adjustor screw Metal M3 x 10 mm
38 2 Motor bulkhead adjustor screw Metal M3 x 16 mm
39 1 Spinner mount Inj. moulded plastic Ready made
40 1 Aero-tow mechanism Inj. moulded plastic Ready made
41 1 Aero-tow release pushrod, one Z-bend Metal 1 Ø x 80 mm
42 2 Fore-and-aft motor support Rectangular plastic tube 10 x 20 x 200 mm
Wire and rod
50 1 Tubular wing spar CFRP tube 10 Ø x 8 Ø x 800 mm
51 2 Pre-formed pushrod, elevator / rudder Metal 0.8 Ø x 492 mm
52 1 Tailwheel pushrod Metal 1.3 Ø x 530 mm
53 3 Snake outer sleeve, ele. / rud. / tailwheel Plastic 3 Ø x 2 Ø x 408 mm
54 2 Snake inner tube, elevator / rudder Plastic 2 Ø x 1 Ø x 450 mm
Undercarriage set
61 2 Lightweight wheel Plastic 73 Ø, 4 mm hub bore
62 2 Socket-head screw Metal M4 x 35 mm
63 2 Nut Metal M4
64 2 Self-locking nut Metal M4
65 4 Washer Metal M4
66 1 Undercarriage support with nut sockets Inj. moulded plastic Ready made
67 2 Flat undercarriage support Inj. moulded plastic Ready made
68 4 Screw
Metal M3 x 45 mm
69 4 Nut Metal M3
70 1 Tailwheel unit Inj. moulded plastic Ready made
71 1 Tailwheel axle Metal 1.6 mm Ø
72 1 Lightweight tailwheel Foam rubber 26 mm Ø
73 4 Collet Metal 2.2 Ø x 7 Ø x 5 mm
74 4 Socket-head grubscrew Metal M3 x 3 mm
75 1 Socket-head grubscrew Metal M3 x 5 mm
76 1 Tailwheel steering lever Inj. moulded plastic Ready made
77 1 Swivel pushrod connector Metal Ready made, 6 mm Ø
78 1 Washer Metal M2
79 1 Nut Metal M2