EasyManuals Logo

MWM D229-3 User Manual

MWM D229-3
82 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #35 background imageLoading...
Page #35 background image
9.229.0.006.2660 - 04/2003 35
ADITIVOS PARA O LÍQUIDO DE
ARREFECIMENTO
Qualquer água, potável ou não,
produzirá corrosão em menor ou maior
intensidade no sistema de arrefe-
cimento.
Também as concentrações de sais e
cálcio na água são prejudiciais pela
formação de depósitos calcáreos nas
superfícies internas do sistema,
afetando a transferência de calor.
Devido a estes fatores, a água a ser
utilizada deve ser limpa e tratada
corretamente com o aditivo
9.0193.05.6.0004 na proporção
recomendada na embalagem.
Aplicações adicionais para manuten-
ção devem ser feitas adicionado-se
água limpa com aditivo na proporção
recomendada na embalagem sempre
que necessário.
Em regiões onde o inverno é muito
rigoroso deve-se tomar precauções
contra a possibilidade de congela-
mento da água do sistema de
arrefecimento. Se houver a tendência
da temperatura ambiente cair abaixo
de 0
o
C, recomendamos o uso de aditivo
anticongelante, que são líquidos
solúveis em água utilizados para evitar
que água do sistema de arrefecimento
se congele.
ADICTIVOS PARA EL LÍQUIDO DE
ENFRIAMIENTO
Cualquer agua, potable o no, producirá
corrosion en menor o mayor intensidad
em el sistema de enfriamiento.
También las concentraciones de sales
y calcio en la água son perjudiciales
por la formacion de depósitos
calcáreos em las superfícies interiores
del sistema, afectando la transferencia
de calor.
Debido a estos factores, la agua a ser
utilisada debe ser limpia y tratada
correctamente con el adictivo
9.0193.05.6.0004 em la proporcion
recomendada en la embalage.
Aplicaciones adicionales para
mantenimiento debem hacerse
añadiendose agua limpia con adictivo
em la proporcion recomendada en la
embalage siempre que necesário.
En regiones onde el invierno es mui
riguroso debese tomar precauciones
contra la posibilidad de helamento de
la agua del sistema de enfriamiento. Si
hay la tendencia de la temperatura
ambiente caer abajo de 0
o
C, se
recomenda el uso de adictivos
anticongelantes, que son líquidos
solubles en agua, utilisados para evitar
que la agua del sistema de
enfriamiento se congele.
COOLING FLUID ADDITIVES
Any water, potable or not, will produce
corrosion of more or less intensity in
the cooling system.
Also the concentration of salts and
calcium in the water produce deposit
formations on the system inner surfaces,
affecting the heat transfer.
Due to these factors, the water to be
used must be clean and treated correctly
with the coolant additive
9.0193.05.6.0004 in the proportions
recommended on the bottle.
Additional make-up coolant should be
made by adding clean water with coolant
additive in the recommended proportion
on the package.
In regions where the winter is very cold,
some precautions must be taken against
the possibility of water freezing in the
cooling system. If the temperatures fall
below 32
o
F zero °C, we recommend the
use of antifreeze, which contains liquid
soluble to avoid freezing of the cooling
system water.

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the MWM D229-3 and is the answer not in the manual?

MWM D229-3 Specifications

General IconGeneral
BrandMWM
ModelD229-3
CategoryEngine
LanguageEnglish

Related product manuals