NAD 3300 - Specifications Overview; Preamplifier Section Specifications; Power Amplifier Section Specifications; Line Level Input and Output Specifications

Specifications
The
3300
Monitor
Series
Amplifier
Note:
Specifications
are
measured
in
accordance
with
EIA
Standard
RS-490
(IHF
A-202).
Measurements
referenced
to
8
ohms
are
taken
with
the
Speaker
Impedance
selector
set
to
“8Q
(High).””
Measurements
for
4
and
2
ohms
are
taken
with
the
impedance
selector
at
“4Q
(Normal).”
Power
Amplifier
Section
CONTINUOUS
AVERAGE
POWER
OUTPUT
INTO
8
OHMS
(min.
RMS
power
per
channel
into
8
ohms,
20Hz~20kHz,
both
channels
driven,
with
no
more
than
the
rated
distortion)
Rated
distortion
(THD),
20Hz-20kHz
Clipping power at 8 ohms
(maximum continuous
power per channel)
IHF dynamic headroom at 8 ohms
IHF
dynamic
power
8
ohms:
(maximum
short-term
4
ohms:
power
per
channel)
2
ohms:
Peak
output
current
(amperes)
Reactive
load
rating
Transient
overload
recovery
time
Slew
factor
Slew rate
Damping
factor
(ref.
8Q
,
at
50
Hz)
Input
impedance
Input
sensitivity
for
rated
power
Input
sensitivity
for
1
watt
out
Power
amplifier
gain
THD
(Total
Harmonic
Distortion;
20H2Z-20kHz,
from
250mW
to
rated
output)
a
whos
=
SMPTE
I.M.
(Intermodulation
Distortion,
60Hz
+
7kHz,
4:1,
from
250mW
to
rated
output)
IHF
LM.
(CCIF
IM
Distortion,
19
+
20
kHz
at
rated
output)
Halli
cd
a
60 W (178 dBW)
0.03% ¥'
70W
+6 dB
250W
300W
400W
>30A
+1.5 dB
<1 usec
>50
30V/ysec
>100
30 kQ
1V
120 mV
28dB (25x)
<0.03% .
<0.03%
<0.03%
Preamplifier Section
Phono Input
Input impedance ({R and C) MM:
MC:
Input sensitivity ref. 1 watt MM:
: MC:
Input overload MM:
THD (20Hz—20kHz) and IM Dist.
at +30 dB level
RIAA response accuracy
S/N ratio, IHF A-weighted, MM:
with cartridge connected MC:
47kQ + 100/200/300 pF
10082 + 1000 pF
0.4mV
0.02 mV
18mV/170MV/1.5V
0.8mV/8mV/70mV
<0.02%
+ 0.3dB
80 dB ref. 5 mV
80 dB ref. 0.5 mV
Line Level Inputs (CD, Video, Tape)
Input impedance
Input sensitivity ref. 1 watt
Maximum input signal
Signal to noise ratio, A~weighted
Frequency response, 20Hz~20kHz
Crosstalk between channels
Crosstalk between inputs
Line-level outputs
Preamp output impedance
- Maximum output level
Tape output impedance
Tape output infrasonic filter
Controls
Treble
Bass
Bass EQ
Infrasonic filter (switchable)
Audio muting (low level)
Physical Specifications
Dimensions (Width x Height x
Depth)
Net Weight
Shipping Weight
Power Consumption
180kQ + 100pF
25 mV
8V rms
100 dB ref. 1 W
118 dB ref. rated power ~~~ - ~---—-----
+ 0.5 dB
60 dB at 1 kHz
50 GB at 20 kHz
70 GB at 1 kHz
60 dB at 20 kHz
8002
10 V
10002 (buffered)
—3dB at 15 Hz, 12 dB/octave
+10 GB at 3, 6, or 12 kHz
+ 10 dB at 50, 100, or 250 Hz
+3 dB at 60 Hz, +6 dB at 32 Hz
—3 dB at 14 Hz, 18 dB/octave
—20 dB
43.2 cm. X10.5 cm. x 38.1 cm.
17 in. x 4.12 in. x 15 in.
10 kg/22 Ib
11.3 kg/25 Ib
375W—110, 120, 220 or 240 VAC
(50/60Hz) ;
NOTE: Specifications are those in effect at the time of printing. NAD reserves the right to
change specifications or designs at any time without notice.