Napa 791-6600 D User Manual

791-6600 D 1 03/16/18
Capacity .................................. 10 Ton
Low Height .................................. 6-5/16"
Raised Height....................................22"
Length ..................................... 60-5/8"
Chassis Width ................................ 7-5/8"
Chassis Width with Swivel Caster Bracket ........ 18-5/16"
Handle Length ............................... 45-3/4"
Saddle Diameter............................... 5-7/8"
Shipping Weight ..............................337 Lbs
MODEL # 791-6600 D
10 TON CAPACITY
SERVICE JACK
SPECIFICATIONS
BEFORE USING THIS DEVICE, READ THIS
MANUAL COMPLETELY AND THOROUGHLY,
UNDERSTAND ITS OPERATING
PROCEDURES, SAFETY WARNINGS AND
MAINTENANCE REQUIREMENTS.
It is the responsibility of the device owner to make sure all personnel
read this manual prior to using the device. It is also the responsibility
of the device owner to keep this manual intact and in a convenient
location for all to see and read. If the manual or product labels are lost
or not legible, contact NAPA for replacements. If the operator is not
fluent in English, the product and safety instructions shall be read to
and discussed with the operator in the operator's native language by
the purchaser/owner or his designee, making sure that the operator
comprehends its contents.
• Read, study, understand and follow all instructions before op-
erating this device. • Inspect the jack before each use. Do not
use jack if damaged, altered, modied, in poor condition, leak-
ing hydraulic uid, or unstable due to loose or missing compo-
nents. Make corrections before using. • Lift only on areas of the
vehicle as specied by the vehicle manufacturer. • Wear eye
protection that meets ANSI Z87.1 and OSHA standards (user
and bystanders). • Do not use jack beyond its rated capacity.
Do not shock load • This is a lifting device only. Immediately
after lifting, support the vehicle with jack stands capable
of sustaining the load before working on the vehicle • Use
only on a hard level surface free from obstructions so the jack
is free to reposition itself during lifting and lowering operations.
• Center load on saddle. Be sure setup is stable before working
on vehicle. • Do not move or dolly the vehicle while on the jack.
• Do not use any materials that may serve as risers, spacers or
extenders between the stock lifting saddle and the load. • Do
not use any adapters that replace the stock lifting saddle unless
approved or supplied by the jack manufacturer. • Do not use (or
modify) this product for any other purpose than that for which it
was designed without consulting the manufacturer's authorized
representative. • Always lower the jack slowly and carefully.
Failure to heed these warnings may result in serious or fatal
personal injury and/or property damage.
WARNING
WARNING: This product can expose you to chemicals
including nickel, which is known to the State of
California to cause cancer and birth defects or other
reproductive harm. For more information go to www.
P65Warnings.ca.gov.
S
A
F
E
T
Y
S
T
A
N
D
A
R
D
C
O
M
P
L
I
E
S
I
T
H
W
ASME PASE-2014

Napa 791-6600 D Specifications

General

Brand	Napa
Model	791-6600 D
Category	Jacks
Language	English

Summary

Introduction and Safety Precautions

Before Using This Device

Read and understand all operating procedures, safety warnings, and maintenance requirements before use.

General Safety Warnings

Important safety precautions and warnings for operating the jack, including potential hazards.

Chemical Exposure Warning

Warning about potential chemical exposure (nickel) and its health effects.

Specifications

Capacity and Dimensions

Lists the maximum load capacity, physical dimensions, and shipping weight of the service jack.

Safety Warnings and Hazard Information

Warning Symbols and General Alerts

Explains safety alert symbols and general warnings indicating potential injury or death.

Operating Instructions Emphasis

Stresses the importance of reading and understanding all instructions before device operation.

Hazardous Situations Overview

Details the nature of hazards, methods to avoid them, and consequences of non-compliance.

Setup and Operation

Handle Assembly Setup

Instructions for installing and verifying the handle assembly alignment.

Purging Air from Hydraulic System

Steps to remove trapped air from the hydraulic system for proper operation.

Raising and Lowering Loads

Detailed procedures for safely lifting and lowering vehicles using the jack.

Preventative Maintenance and Storage

General Maintenance Guidelines

Basic rules for protecting the jack from elements and ensuring lubrication.

Hydraulic System Maintenance

Guidelines for hydraulic fluid, avoiding contamination, and seal protection.

Proper Storage

Recommendations for storing the jack in a dry, protected environment.

Troubleshooting and User Responsibility

Troubleshooting Common Problems

Lists common issues like unit not lifting or feeling spongy, and their recommended solutions.

Owner/User Responsibility

Defines the owner's and operator's duties regarding understanding and maintaining instructions.

Parts Identification

Exploded View Diagram

Visual representation of the jack's components with part numbers.

Component Parts List

Detailed list of all parts for the service jack and power unit with quantities.