Essential Safety Precautions
• To avoid a possibility of electrical shock, be sure to connect the power cord to the Panther Fuel Controller before
connecting it to the A/C power outlet.
• A fire or electrical shock may result if the voltage used with the Panther Fuel Controller is beyond the specified range.
• Voltage and frequency rating: 100V – 240V AC, 60 – 50Hz, 2A.
• To prevent a possible explosion, do not install the Panther Fuel Controller in areas which contain flammable gases.
• Do not cover or install in an enclosed space.
• The Panther Fuel Controller is not water resistant and should not be installed in areas where it may be exposed to water
or other moisture.
• Use only 26AWG telecommunication line cord when connecting the optional modem.
• The operating temperature range of this device is 32 to 122 F (0 to 50 C). Do not operate the device if the ambient
temperature is not within this range.
IT Power System
The NCR Panther Fuel Controller is suitable for connection to an IT power system with a phase‐to‐phase voltage not
exceeding 240 V.
This device is not intended for use as a workstation.
Cet appareil n’est pas destine à servir d’ordinateur de travail.
Dieses Geräte kann nicht als Arbeitsplatz verwendet werden
Servicing
Warning: This product does not contain user serviceable parts. Servicing should only be performed by a qualified
service technician.
Attention: Ce produit ne contient pas de components reparable par l’utilisateur. Le service ne doit être fait que par un
technicien qualifié.
Warnung: Dieses Produkt enthält keine verbrauchbaren Teile. Service nur durch einen qualifizierten Fachmann.
Fuse Replacement
Warning: For continued protection against risk of fire, replace only with the same type and ratings of fuse.
Attention: Pour prévenir et vous protéger contre un risque de feu, remplacer la fusible avec une autre fusible de même
type, seulement.
Achtung: Gegen schutz vor feuer; ersetzen sie nur sicherungen der selben art und wertung
Power Supply Cord Used as Disconnect Means
Warning: The power supply cord is used as the main disconnect device. Ensure that the socket outlet is
located/installed near the equipment and is easily accessible.
Attention: Le cordon dʹalimentation est utilisé comme interrupteur général. La prise
de courant doit être située ou installée à proximité du matériel et être facile à acceder.
Warnung: Der Stromstecker sollte nahe dem Geräte installiert sein und sollte leicht
zugänglich sein.
AC Power Cord Usage
The attached power cord should only be used with this device. It must not be used with any other device.
Connecting to an AC Source
See the AC requirements in the Site Preparation Guide before connecting to the AC supply.
Voir les exigences de courant alternatif dans le Guide de Préparation de Site avant le fait de raccorder aux réserves de
courant alternatif.
Lithium Battery Warning
Warning: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type as
recommended by the manufacturer. Discard used batteries according to the manufacturerʹs instructions.
Attention: Il y a danger dʹexplosion sʹil y a remplacement incorrect de la batterie. Remplacer uniquement avec une
batterie du même type ou dʹun type recommandé par le constructeur. Mettre au rebute les batteries usagées
conformément aux
instructions du fabricant.
Warnung:: Gefahr von Explosionen wenn die Batterie falsch eingelegt wird. Ersetzen Sie nur mit gleichen oder
gleichwertigen Batterien wie vom Hersteller empfohlen. Entsorgen Sie die Batterien wie vom Hersteller empfohlen.
Battery Disposal (Switzerland)
Refer to Annex 4.10 of SR814.013 for battery disposal.
Peripheral Usage
This terminal should only be used with peripheral devices that are certified by the appropriate safety agency for the
country of installation (e.g. UL, CSA, TUV, VDE) or those which are recommended by NCR Corporation.
Ce terminal devrait être utilisé avec les mécanismes périphériques qui sont certifiés par l’agence appropriée pour le
pays d’installation (UL, CSA, TUV, VDE) ou ceux recommandés par la NCR Corporation. Dieses Terminal sollte nur mit
peripheren Geräten benutzt werden die von der geeigneten Sicherheitsagentur für das Land in dem es installiert wird
(UL, CSA, TUV, VDE) oder jenen die von der NCR empfohlen werden, angeschlossen werden.
Warning: DO NOT connect or disconnect a printer, keyboard, or any other terminal‐powered peripheral while the
terminal is powered on. Doing so may result in peripheral or system damage.
System Weight Considerations for Wall or Ceiling Mounted Equipment
Warning: NCR Panther Fuel Controller must be mounted securely to prevent a hazard. They must be installed in
accordance with local building codes. The location where the unit is installed should be able to withstand four times the
weight of the unit
Attention – Le NCR Panther Fuel Controller doit être installer précautionneusement afin d’éviter tout accident éventuel.
Il doit être installé dans le respect des codes de l’établissement.
Warnung: Der NCR Panther Fuel Controller muss sicher montiert werden um Gefahr zu verhindern. Es muss in
Übereinstimmung mit den örtlichen Bauvorschriften installiert werden.
Panther Fuel Controller Quick Reference Guide - 1651
Follow the instructions below to ensure the safe mounting of the Panther Fuel Controller.
• The AC outlet should be installed near the Panther and be easily accessible.
• Appropriate Hex or Philips head screw driver is required to seat screws. Electric screw
driver and applicable bits are required to create pilot holes for either screw or wall anchor.
Wall Mounting
1) Verify the conduit coupling is tightly installed. If necessary, remove any additional knockout
holes and install additional conduit couplings.
2) Attach the wall mount bracket to the wall through the 4 wall mounting holes. Where
possible, ensure that at least one vertical pair of mounting holes will be mounted to a stud.
For stud mounting use ¼” diameter x 2” length wood screws. The other hole pair will be
mounted with¼” diameter x 2 ¼” length hollow wall anchors. If there are no studs available,
hollow wall anchors may be used for all mounting holes.
¼” diameter, 2 ¼” length Wood Screw
¼” diameter, 2 ¼” length Hollow Wall Anchor
Mounting Bracket Installation
Recovery Utility And Power Button Instructions
Pressing the Recovery Button on the side of the unit during initial boot will cause the Panther
Fuel Controller to boot to its Recovery Mode. This operation will automatically run a check disk
process to attempt to resolve any problems with the disk or file system and then reboot into
Normal Mode. A text file log of any changes will be created on the storage card.
Pressing the Power Button on the side of the unit will cause the Panther Fuel Controller to turn
on. To power off the unit, press and hold the Power Button for 4 to 5 seconds.
Recovery
Power
Page 5
497-0503689 Rev C
To Next Page
Loading...
