EasyManuals Logo

NEC MultiSync LCD2490WUXi User Manual

NEC MultiSync LCD2490WUXi
136 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #7 background imageLoading...
Page #7 background image
4
Make sure to leave enough slack in the cables so that the Tilt and the
Raise and Lower functions of the monitor are not impeded.
6. Hold all of the cablesrmly and place the cable cover onto the
stand (Figure 8).
7. Slide the Cable Cover back into its correct position (Figure 9).
Connect the power cord to power outlet.
NOTE: Please refer to the Recommended Use section of this manual for
proper selection of power cord.
8. The vacation switch on the left side of the monitor must be in the
ON position for the monitor to function (Figure 10).
Turn on the monitor using the front power button, then turn on the computer.
NOTE: The Vacation Switch is a true on/off switch. If this
switch is in the OFF position, the monitor cannot be
turned on using the front button.
DO NOT turn the vacation switch ON/OFF repeatedly.
9. For Analog input only: Upon initial setup, the No-Touch Auto Adjust feature
automatically adjusts the monitor to the optimal settings that are needed for
most signal timings.
For further adjustments, refer to the Controls section of this Users Manual
for a full description of the OSM controls.
For download information on the Windows
®
INF file for your monitor, visit www.
necdisplay.com/support.
NOTE: If you have any problems, please refer to the Troubleshooting
section of this User’s Manual.
Highest
Stand
Position
Power cord
DC-OUT
DVI-D
DVI-I
D-SUB
30 Tilt
Figure 4 Figure 5
Figure 6
Quick Start – continued
(DC out for optional NEC products such as
the Soundbar attachment. Do not use this
connector unless specified.)

Other manuals for NEC MultiSync LCD2490WUXi

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the NEC MultiSync LCD2490WUXi and is the answer not in the manual?

NEC MultiSync LCD2490WUXi Specifications

General IconGeneral
3DNo
HD type-
Pixel pitch0.27 x 0.27 mm
Aspect ratio16:10
Response time8 ms
Display surfaceMatt
Display diagonal24 \
Separate H/V syncYes
Display resolution1920 x 1200 pixels
Vertical scan range50 - 85 Hz
Horizontal scan range31.5 - 93.8 kHz
Contrast ratio (typical)800:1
Display number of colors16.78 million colors
Digital horizontal frequency31.5 - 119.2 kHz
Display brightness (typical)400 cd/m²
Supported graphics resolutions720 x 400, 832 x 624, 1152 x 870, 1280 x 960, 1024 x 768 (XGA), 1280 x 1024 (SXGA), 1600 x 1200 (UXGA), 1920 x 1200 (WUXGA), 640 x 480 (VGA), 800 x 600 (SVGA)
HDMI ports quantity0
Product colorBlack
Panel mounting interface100 x 100 mm
AC input voltage100 - 240 V
Power consumption (standby)1 W
Power consumption (typical)83 W
Storage temperature (T-T)-10 - 60 °C
Operating temperature (T-T)5 - 35 °C
Storage relative humidity (H-H)10 - 85 %
Operating relative humidity (H-H)30 - 80 %
Cables includedAC
Weight and Dimensions IconWeight and Dimensions
Depth (with stand)104 mm
Height (with stand)359.8 mm
Weight (with stand)11800 g
Depth (without stand)306 mm
Width (without stand)554.2 mm
Height (without stand)432.4 mm
Weight (without stand)8400 g

Related product manuals